I insert another new NIC in the machine with four RJ45 connector options(means four NICs in one Card). The problem is i am not able to see the new NIC
That is the expected behavior. You need to configure the OS to add these interfaces.
Then create /etc/hostname.xxx for each interface you want to be plumbed at next boot, each file containing the required IP address. xxx being the interface name (eg. qfe0, qfe1, ...)
All,
I see that there are 2 nic card available . How can I know all the details about these 2 nic cards.
-rw-r--r-- 1 root root 10 Apr 16 15:00 hostname.bge0
-rw-r--r-- 1 root other 17 Apr 22 08:56 hostname.bge2
please let me know
thanks
-prasad (4 Replies)
Hi , I came across a SUN server whereby it was installed with additional ethernet card. By right in any configuration, you would probably see the onboard ports Net0,Net1 and so on should correspond to e1000g0,e1000g1...
But instead the ext PCI takes precedence in the order and the Net0 becomes... (3 Replies)
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Hi all,
I'm having some trouble identifying what route is being used to talk to a target host. I can figure it out by looking at the routing tables but I want to automate this and don't much feel like scripting the network mask logic when I'd think there'd be a way to have the OS do it for me.... (5 Replies)
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
LEARN ABOUT BSD
hosts
HOSTS(5) File Formats Manual HOSTS(5)NAME
hosts - host name data base
DESCRIPTION
The hosts file contains information regarding the known hosts on the network. For each host a single line should be present with the fol-
lowing information:
official host name
Internet address
aliases
Items are separated by any number of blanks and/or tab characters. A ``#'' indicates the beginning of a comment; characters up to the end
of the line are not interpreted by routines which search the file.
When using the name server named(8), this file provides a backup when the name server is not running. For the name server, it is suggested
that only a few addresses be included in this file. These include address for the local interfaces that ifconfig(8C) needs at boot time
and a few machines on the local network.
This file may be created from the official host data base maintained at the Network Information Control Center (NIC), though local changes
may be required to bring it up to date regarding unofficial aliases and/or unknown hosts. As the data base maintained at NIC is incom-
plete, use of the name server is recommend for sites on the DARPA Internet.
Network addresses are specified in the conventional ``.'' notation using the inet_addr() routine from the Internet address manipulation
library, inet(3N). Host names may contain any printable character other than a field delimiter, newline, or comment character.
FILES
/etc/hosts
SEE ALSO gethostbyname(3N), ifconfig(8C), named(8)
Name Server Operations Guide for BIND
4.2 Berkeley Distribution May 14, 1986 HOSTS(5)