Not able to find the new NIC Post: 302516423

9 More Discussions You Might Find Interesting

1. Solaris

How do I find what kind of NIC card the server has?

All, I see that there are 2 nic card available . How can I know all the details about these 2 nic cards. -rw-r--r-- 1 root root 10 Apr 16 15:00 hostname.bge0 -rw-r--r-- 1 root other 17 Apr 22 08:56 hostname.bge2 please let me know thanks -prasad

2. Solaris

Cause of NIC changes ...?

Hi , I came across a SUN server whereby it was installed with additional ethernet card. By right in any configuration, you would probably see the onboard ports Net0,Net1 and so on should correspond to e1000g0,e1000g1... But instead the ext PCI takes precedence in the order and the Net0 becomes...

3. HP-UX

how can I determine which NIC card is virtual NIC Card

how can I determine which NIC card is virtual NIC Card which condition can make a decision Does HP UX have Virtual Network Adapter Concept if ,it has where I can Find if I Install Virutal Network Adapter or which command that i can get it or which software can generate thanks

4. AIX

AIX -How to find which NIC is on which PCI card

Hi All, How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v Any idea? Thanks.

5. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux...

6. IP Networking

squid proxy: one NIC for inbound & one NIC for outbound?

I am new in squid proxy. My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)? Thank you in advance!

7. Solaris

How can I find which NIC is used to talk to a given host (except traceroute)

Hi all, I'm having some trouble identifying what route is being used to talk to a target host. I can figure it out by looking at the routing tables but I want to automate this and don't much feel like scripting the network mask logic when I'd think there'd be a way to have the OS do it for me....

8. Red Hat

I want to tune NIC's rps, rfs and xps value. which NIC device should I modify.

Dear All I want tune my NIC's rps, rfs and xps value. In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1). Here is the question? Which device should I modify ? eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0) Any advice is welcome....

9. Linux

Add two different subnet public IPs to single NIC or two different NIC on same box

Hello Admins, My ask is how can I add two different subnet IPs to same box with two different gateways? The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware. How can I get connected...

LEARN ABOUT HPUX

systemd-timesyncd.service

SYSTEMD-TIMESYNCD.SERVICE(8)				     systemd-timesyncd.service				      SYSTEMD-TIMESYNCD.SERVICE(8)

NAME

       systemd-timesyncd.service, systemd-timesyncd - Network Time Synchronization

SYNOPSIS

       systemd-timesyncd.service

       /lib/systemd/systemd-timesyncd

DESCRIPTION

       systemd-timesyncd is a system service that may be used to synchronize the local system clock with a remote Network Time Protocol server. It
       also saves the local time to disk every time the clock has been synchronized and uses this to possibly advance the system realtime clock on
       subsequent reboots to ensure it monotonically advances even if the system lacks a battery-buffered RTC chip.

       The systemd-timesyncd service specifically implements only SNTP. This minimalistic service will set the system clock for large offsets or
       slowly adjust it for smaller deltas. More complex use cases are not covered by systemd-timesyncd.

       The NTP servers contacted are determined from the global settings in timesyncd.conf(5), the per-link static settings in .network files, and
       the per-link dynamic settings received over DHCP. See systemd.network(5) for more details.

       timedatectl(1)'s set-ntp command may be used to enable and start, or disable and stop this service.

FILES

       /var/lib/systemd/timesync/clock
	   This file contains the timestamp of the last successful synchronization.

SEE ALSO

       systemd(1), timesyncd.conf(5), systemd.network(5), systemd-networkd.service(8), timedatectl(1), localtime(5), hwclock(8)

systemd 237													      SYSTEMD-TIMESYNCD.SERVICE(8)