04-23-2011
cat /etc/path_to_inst |grep -i network
The above will give you the required info..
9 More Discussions You Might Find Interesting
1. Solaris
All,
I see that there are 2 nic card available . How can I know all the details about these 2 nic cards.
-rw-r--r-- 1 root root 10 Apr 16 15:00 hostname.bge0
-rw-r--r-- 1 root other 17 Apr 22 08:56 hostname.bge2
please let me know
thanks
-prasad (4 Replies)
Discussion started by: p4cldba
4 Replies
2. Solaris
Hi , I came across a SUN server whereby it was installed with additional ethernet card. By right in any configuration, you would probably see the onboard ports Net0,Net1 and so on should correspond to e1000g0,e1000g1...
But instead the ext PCI takes precedence in the order and the Net0 becomes... (3 Replies)
Discussion started by: incredible
3 Replies
3. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
4. AIX
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
Discussion started by: samnyc
2 Replies
5. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
6. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
7. Solaris
Hi all,
I'm having some trouble identifying what route is being used to talk to a target host. I can figure it out by looking at the routing tables but I want to automate this and don't much feel like scripting the network mask logic when I'd think there'd be a way to have the OS do it for me.... (5 Replies)
Discussion started by: Smiling Dragon
5 Replies
8. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
9. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
LEARN ABOUT DEBIAN
expect_unbuffer
UNBUFFER(1) General Commands Manual UNBUFFER(1)
NAME
unbuffer - unbuffer output
SYNOPSIS
unbuffer program [ args ]
INTRODUCTION
unbuffer disables the output buffering that occurs when program output is redirected from non-interactive programs. For example, suppose
you are watching the output from a fifo by running it through od and then more.
od -c /tmp/fifo | more
You will not see anything until a full page of output has been produced.
You can disable this automatic buffering as follows:
unbuffer od -c /tmp/fifo | more
Normally, unbuffer does not read from stdin. This simplifies use of unbuffer in some situations. To use unbuffer in a pipeline, use the
-p flag. Example:
process1 | unbuffer -p process2 | process3
CAVEATS
unbuffer -p may appear to work incorrectly if a process feeding input to unbuffer exits. Consider:
process1 | unbuffer -p process2 | process3
If process1 exits, process2 may not yet have finished. It is impossible for unbuffer to know long to wait for process2 and process2 may
not ever finish, for example, if it is a filter. For expediency, unbuffer simply exits when it encounters an EOF from either its input or
process2.
In order to have a version of unbuffer that worked in all situations, an oracle would be necessary. If you want an application-specific
solution, workarounds or hand-coded Expect may be more suitable. For example, the following example shows how to allow grep to finish pro-
cessing when the cat before it finishes first. Using cat to feed grep would never require unbuffer in real life. It is merely a place-
holder for some imaginary process that may or may not finish. Similarly, the final cat at the end of the pipeline is also a placeholder
for another process.
$ cat /tmp/abcdef.log | grep abc | cat
abcdef
xxxabc defxxx
$ cat /tmp/abcdef.log | unbuffer grep abc | cat
$ (cat /tmp/abcdef.log ; sleep 1) | unbuffer grep abc | cat
abcdef
xxxabc defxxx
$
BUGS
The man page is longer than the program.
SEE ALSO
"Exploring Expect: A Tcl-Based Toolkit for Automating Interactive Programs" by Don Libes, O'Reilly and Associates, January 1995.
AUTHOR
Don Libes, National Institute of Standards and Technology
1 June 1994 UNBUFFER(1)