Well, you can delete everything and copy afresh:
or go by modified date, checksum or bit for bit compare of every file. Do you need to trim excess files in /appabc2/ ? New files need to be added, of course. Can there be new dirs? See man cpio pass option with updates only, which does a lot of this. The rsync command seems overkill for local files. Off the cuff = untested, files only, exact compare:
I'm having this error when I do full fs cleanup
# fsck -F vxfs -o full /dev/vg01/lvol1
vxfs fsck: file system had I/O error(s) on meta-data.
log replay in progress
vxfs fsck: file system had I/O error(s) on meta-data.
vxfs fsck: file system had I/O error(s) on meta-data.
pass0 - checking... (2 Replies)
I am using raidctl on a v440 disk and noticed it resyncs after every boot, which takes about 30 minutes because of the size of the partition. I am concerned with what happens during the resync if "writes" happen to the disk before it is complete?
Any info would be helpful.
Thanks (0 Replies)
Hey peeps,
Here is somethin u might find interestin....
Is it possible to recover data from a partition which used to be an ext3 file sytem with some nice forgotten backups, which now is an lvm partion containg root partition of another OS. :)
I couldn't create any mess better than this, can... (2 Replies)
Hi All,
I am writing a block driver for a 2GB SD card where i get the total amount of data per request as follows:
struct request *req;
uint card_addr,total_bytes;
struct request_queue *rq = BlkDev->queue;
req = elv_next_request(rq);
..
..
card_addr = req->sector*512;... (1 Reply)
Hi,
could any one tell is there any test-suite or any idea How to do data corruption validation testing, means there is no any data corruption ?
Regards
Manish (1 Reply)
Hi,
In order to have a sand box machine that I could use to test some system changes before going to production state, I'd like to duplicate a working system to a virtual one. Ideally, I'd like to manage to do it this way :
- Make a full system backup excluding the user file system (this... (7 Replies)
In my infinite lack of wisdom, I brought a Solaris 10(Sparc, 64 bit ) system down to init 1, detached a metadrive so that I could run format->analyze->refresh on it, and then reinit'd and reattached it .
It started syncing the drive as it's a submirror of a mirrored drive, which happens... (8 Replies)
/tmp/man18809436: Invalid file system control data detected
Help me
what do I do?
Если знаете русскии, пишите на нем. (2 Replies)
Discussion started by: islily
2 Replies
LEARN ABOUT OSX
locale::codes::langvar
Locale::Codes::LangVar(3pm) Perl Programmers Reference Guide Locale::Codes::LangVar(3pm)NAME
Locale::Codes::LangVar - standard codes for language variation identification
SYNOPSIS
use Locale::Codes::LangVar;
$lvar = code2langvar('acm'); # $lvar gets 'Mesopotamian Arabic'
$code = langvar2code('Mesopotamian Arabic'); # $code gets 'acm'
@codes = all_langvar_codes();
@names = all_langvar_names();
DESCRIPTION
The "Locale::Codes::LangVar" module provides access to standard codes used for identifying language variations, such as those as defined in
the IANA language registry.
Most of the routines take an optional additional argument which specifies the code set to use. If not specified, the default IANA language
registry codes will be used.
SUPPORTED CODE SETS
There are several different code sets you can use for identifying language variations. A code set may be specified using either a name, or
a constant that is automatically exported by this module.
For example, the two are equivalent:
$lvar = code2langvar('en','alpha-2');
$lvar = code2langvar('en',LOCALE_CODE_ALPHA_2);
The codesets currently supported are:
alpha
This is the set of alphanumeric codes from the IANA language registry, such as 'arevela' for Eastern Armenian.
This code set is identified with the symbol "LOCALE_LANGVAR_ALPHA".
This is the default code set.
ROUTINES
code2langvar ( CODE [,CODESET] )
langvar2code ( NAME [,CODESET] )
langvar_code2code ( CODE ,CODESET ,CODESET2 )
all_langvar_codes ( [CODESET] )
all_langvar_names ( [CODESET] )
Locale::Codes::LangVar::rename_langvar ( CODE ,NEW_NAME [,CODESET] )
Locale::Codes::LangVar::add_langvar ( CODE ,NAME [,CODESET] )
Locale::Codes::LangVar::delete_langvar ( CODE [,CODESET] )
Locale::Codes::LangVar::add_langvar_alias ( NAME ,NEW_NAME )
Locale::Codes::LangVar::delete_langvar_alias ( NAME )
Locale::Codes::LangVar::rename_langvar_code ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangVar::add_langvar_code_alias ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangVar::delete_langvar_code_alias ( CODE [,CODESET] )
These routines are all documented in the Locale::Codes::API man page.
SEE ALSO
Locale::Codes
The Locale-Codes distribution.
Locale::Codes::API
The list of functions supported by this module.
http://www.iana.org/assignments/language-subtag-registry
The IANA language subtag registry.
AUTHOR
See Locale::Codes for full author history.
Currently maintained by Sullivan Beck (sbeck@cpan.org).
COPYRIGHT
Copyright (c) 2011-2012 Sullivan Beck
This module is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.16.2 2012-10-11 Locale::Codes::LangVar(3pm)