Well, you can delete everything and copy afresh:
or go by modified date, checksum or bit for bit compare of every file. Do you need to trim excess files in /appabc2/ ? New files need to be added, of course. Can there be new dirs? See man cpio pass option with updates only, which does a lot of this. The rsync command seems overkill for local files. Off the cuff = untested, files only, exact compare:
I'm having this error when I do full fs cleanup
# fsck -F vxfs -o full /dev/vg01/lvol1
vxfs fsck: file system had I/O error(s) on meta-data.
log replay in progress
vxfs fsck: file system had I/O error(s) on meta-data.
vxfs fsck: file system had I/O error(s) on meta-data.
pass0 - checking... (2 Replies)
I am using raidctl on a v440 disk and noticed it resyncs after every boot, which takes about 30 minutes because of the size of the partition. I am concerned with what happens during the resync if "writes" happen to the disk before it is complete?
Any info would be helpful.
Thanks (0 Replies)
Hey peeps,
Here is somethin u might find interestin....
Is it possible to recover data from a partition which used to be an ext3 file sytem with some nice forgotten backups, which now is an lvm partion containg root partition of another OS. :)
I couldn't create any mess better than this, can... (2 Replies)
Hi All,
I am writing a block driver for a 2GB SD card where i get the total amount of data per request as follows:
struct request *req;
uint card_addr,total_bytes;
struct request_queue *rq = BlkDev->queue;
req = elv_next_request(rq);
..
..
card_addr = req->sector*512;... (1 Reply)
Hi,
could any one tell is there any test-suite or any idea How to do data corruption validation testing, means there is no any data corruption ?
Regards
Manish (1 Reply)
Hi,
In order to have a sand box machine that I could use to test some system changes before going to production state, I'd like to duplicate a working system to a virtual one. Ideally, I'd like to manage to do it this way :
- Make a full system backup excluding the user file system (this... (7 Replies)
In my infinite lack of wisdom, I brought a Solaris 10(Sparc, 64 bit ) system down to init 1, detached a metadrive so that I could run format->analyze->refresh on it, and then reinit'd and reattached it .
It started syncing the drive as it's a submirror of a mirrored drive, which happens... (8 Replies)
/tmp/man18809436: Invalid file system control data detected
Help me
what do I do?
Если знаете русскии, пишите на нем. (2 Replies)
Discussion started by: islily
2 Replies
LEARN ABOUT OSX
showmount
SHOWMOUNT(8) BSD System Manager's Manual SHOWMOUNT(8)NAME
showmount -- show remote NFS mounts on host
SYNOPSIS
showmount [-Ae36] [-a | -d] [host]
DESCRIPTION
showmount shows status information about the NFS server on host. By default it prints the names of all hosts that have NFS file systems
mounted on the host. See NFS: Network File System Protocol Specification, RFC 1094, Appendix A, and NFS: Network File System Version 3
Protocol Specification, Appendix I, for a detailed description of the protocol.
-A Search for NFS servers advertised via Bonjour.
-a List all mount points in the form: host:dirpath
-d List directory paths of mount points instead of hosts.
-e Show the host's exports list.
-3 Use mount protocol Version 3, compatible with NFS Version 3.
-6 Use only IPv6 addresses to contact servers.
SEE ALSO mount(1), mountd(8), nfsd(8), mDNSResponder(8)BUGS
The mount daemon running on the server only has an idea of the actual mounts, since the NFS server is stateless. showmount will only display
the information as accurately as the mount daemon reports it.
HISTORY
The showmount utility first appeared in 4.4BSD.
4th Berkeley Distribution September 26, 2010 4th Berkeley Distribution