04-14-2011
How to Calculate Disk Queue length and Disk Busy Time
Hi,
Am doing an enhancements related to monitoring a Linux disk I/O statistics.
The /proc/diskstats file is used to get the each disk I/O statistics. But, It returns the raw value.
How to calculate the Disk Queue Length and Disk Busy time from the raw values.
Guide me.
8 More Discussions You Might Find Interesting
1. AIX
hi,
AIX 5.3
For any command(say tar command) I am getting 100% busy for my hdisk.
But my CPU and Memory is not busy and have more idle also.
Please advice for any performance analysing.
Thanks in Advance, (3 Replies)
Discussion started by: npcrao
3 Replies
2. Shell Programming and Scripting
Hello,
I'm writing a script to monitor different filesystems in multiple servers. And depending on the % free, my script will send an Alert email if % free is less than threshold.
I want to keep a input_feed_file which would have "server,filesystem".
If I run a script a host 'a', then I can... (3 Replies)
Discussion started by: bperl
3 Replies
3. Solaris
Previously , i remove the disk by
#vxdg -g testdg -k rmdisk testdg02
But i got error when i -k adddisk
bash-2.03# vxdisk list
DEVICE TYPE DISK GROUP STATUS
c0t0d0s2 auto:none - - online invalid
c0t1d0s2 auto:none ... (1 Reply)
Discussion started by: waibabe
1 Replies
4. Linux
A product I am working on manages storage. We are currently porting it from Solaris to Linux.
The product allows its user, among other things, to add and remove file server volumes, where these volumes are exported using the NFS or the CIFS protocol.
The problem is that when the user requests to... (5 Replies)
Discussion started by: dhzdh
5 Replies
5. AIX
Hi Everyone,
anyone know how to derive the value for the total disk busy % (shown in topas ) ?
Thanks.
Best Regards,
ckwan (1 Reply)
Discussion started by: ckwan
1 Replies
6. AIX
Please help with command to check the busy % for a hard disk device like hdisk5
Best regards,
Vishal (7 Replies)
Discussion started by: Vishal_dba
7 Replies
7. AIX
Hi ,
Following alerts are coming for %busy device on a server
Disk Device hdisk5 is 100% busy
Please assist how do I analyse this and also how do I check the %age busy for hdisk5.
Best regards,
Vishal (4 Replies)
Discussion started by: Vishal_dba
4 Replies
8. Filesystems, Disks and Memory
Hello,
On 4/20/2018, we performed a disk replacement on our IBM 8202 P7 server. After the disk was rebuilt, the SAS Disk Array sissas0 showed a status of degraded. However, the pdisks in the array all show a status of active.
We did see a message in errpt. DISK ARRAY PROTECTION SUSPENDED.
... (1 Reply)
Discussion started by: terrya
1 Replies
LEARN ABOUT OSF1
disklabel
disklabel(4) Kernel Interfaces Manual disklabel(4)
NAME
disklabel - Disk pack label
SYNOPSIS
#include <sys/disklabel.h>
DESCRIPTION
Each disk or disk pack on a system may contain a disk label which provides detailed information about the geometry of the disk and the par-
titions into which the disk is divided. It should be initialized when the disk is formatted, and may be changed later with the disklabel
program. This information is used by the system disk driver and by the bootstrap program to determine how to program the drive and where
to find the file systems on the disk partitions. Additional information is used by the file system in order to use the disk most effi-
ciently and to locate important file system information. The description of each partition contains an identifier for the partition type
(standard file system, swap area, etc.). The file system updates the in-core copy of the label if it contains incomplete information about
the file system.
The label is located in sector number LABELSECTOR of the drive, usually sector 0 (zero) where it may be found without any information about
the disk geometry. It is at an offset LABELOFFSET from the beginning of the sector, to allow room for the initial bootstrap. The disk
sector containing the label is normally made read-only so that it is not accidentally overwritten by pack-to-pack copies or swap opera-
tions; the DIOCWLABEL ioctl, which is done as needed by the disklabel program, allows modification of the label sector.
A copy of the in-core label for a disk can be obtained with the DIOCGDINFO ioctl; this works with a file descriptor for a block or charac-
ter (raw) device for any partition of the disk. The in-core copy of the label is set by the DIOCSDINFO ioctl. The offset of a partition
cannot generally be changed, nor made smaller while it is open. One exception is that any change is allowed if no label was found on the
disk, and the driver was able to construct only a skeletal label without partition information. Finally, the DIOCWDINFO ioctl operation
sets the in-core label and then updates the on-disk label; there must be an existing label on the disk for this operation to succeed.
Thus, the initial label for a disk or disk pack must be installed by writing to the raw disk. All of these operations are normally done
using the disklabel program.
RELATED INFORMATION
Files: disktab(4)
Commands: disklabel(8) delim off
disklabel(4)