04-13-2011
Getting RAID to properly autodetect isn't trivial, which is probably why they decided to get that working for them if anyone needed it.
10 More Discussions You Might Find Interesting
1. Red Hat
We have a Red Hat linux server running on IBM x445 hardware. There are external disks in an IBM EXP300 disk enclosure. The system is running RAID 5. One of the four IBM disks (73.4 GB 10k FRU 06P5760) has become faulty. The system is still up and running OK because of the RAID. In that same EXP300... (3 Replies)
Discussion started by: pdudley
3 Replies
2. Solaris
Hi.
I need to move a 5 disk RAID5 array from a SE3310 box to a different SE3310 array. After installing the disks in the "new" StorEdge device, I "would like" ;) to be able have access to the data which is on the RAID.
Essentially, the quesion is, how can this be done? :confused:
I checked... (5 Replies)
Discussion started by: alexs77
5 Replies
3. Red Hat
I have an HP blade with Qlogic HBA's connected to an EVA8000. I have downloaded the latest multipath.conf from HP's website. The drive presented to the server appears to be configured and working except the output of "multipath -l" shows for all paths. What is causing this output?
mpath0... (2 Replies)
Discussion started by: manzier
2 Replies
4. Red Hat
Hi,
I had a doubt regarding device mapper notations and their corresponding LVM volumes.
I have configured a volume group with two logical volumes in it as root and swap.
The entries in the /etc/fstab file show the dm notations namely,
/dev/mapper/VolGroup00-LogVol01... (2 Replies)
Discussion started by: kanna_geekworkz
2 Replies
5. Solaris
I've just installed Sol 10 Update 9 on a Sun 4140 server and have a RAID 1 configuration (2 136 Gb drives) for the OS and have created a RAID 5 array (6 136 GB) drives. When i log into the system I am unable to see the RAID 5 disks at all. I've tried using the devfsadm command but no luck and... (9 Replies)
Discussion started by: goose25
9 Replies
6. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
7. Red Hat
Good morning
Recently we needed to change the password from a redhat 6.5 system that no one knew the root password.
Starting the system with the init=/bin/bash method took us to the following scenario:
system_vg active with only root_lv and tmpfs mounted.
our entries at fstab are like... (1 Reply)
Discussion started by: Ikaro0
1 Replies
8. Solaris
Dear All ,
Pl find the below command ,
# raidctl -l
Controller: 1
Volume:c1t0d0
Disk: 0.0.0
Disk: 0.1.0
Disk: 0.3.0
#
raidctl -l c1t0d0
Volume Size Stripe Status Cache RAID
Sub Size ... (10 Replies)
Discussion started by: jegaraman
10 Replies
9. UNIX for Advanced & Expert Users
Currently I am using this laborious command
lvdisplay | awk '/LV Path/ {p=$3} /LV Name/ {n=$3} /VG Name/ {v=$3} /Block device/ {d=$3; sub(".*:", "/dev/dm-", d); printf "%s\t%s\t%s\n", p, "/dev/mapper/"v"-"n, d}'
Would like to know if there is any shorter method to get this mapping of... (2 Replies)
Discussion started by: royalibrahim
2 Replies
10. Ubuntu
I suddenly don't see my folders into /mnt/md0.
What can be reason?
mdadm --detail /dev/md*
/dev/md0:
Version : 1.2
Creation Time : Fri Jan 18 09:54:27 2019
Raid Level : raid1
Array Size : 1953383488 (1862.89 GiB 2000.26 GB)
Used Dev Size : 1953383488 (1862.89 GiB... (8 Replies)
Discussion started by: tomislav91
8 Replies
LEARN ABOUT DEBIAN
raidfile.conf
RAIDFILE.CONF(5) Box Backup RAIDFILE.CONF(5)
NAME
raidfile.conf - Userland RAID for Box Backup
SYNOPSIS
/etc/box/raidfile.conf
DESCRIPTION
The raidfile.conf is usually generated by raidfile-config(8) but may be manually edited if the store locations move or if more than one
disc set is required.
discX
Specifies a set of discs.
SetNumber
The set number of the RAID disc, referenced by each account.
BlockSize
The block size of the file system (usually 2048). Under BSD with FFS, set this to your file system's fragment size (most likely an
8th of the block size).
Dir0
The first directory in the RAID array.
Dir1
The second directory in the RAID array. If you do not wish to use the built-in RAID functionality, this field should be set to the
same as Dir0. You should not use the built-in RAID if you have a hardware RAID solution or if you're using another type of software
RAID (like md on Linux).
Dir2
The third directory in the RAID array. The same notes that apply to Dir2 also apply to Dir3.
FILES
/etc/box/raidfile.conf
SEE ALSO
raidfile-config(8), bbstored.conf(5)
AUTHORS
Ben Summers
Per Thomsen
James O'Gorman
Box Backup 0.11 10/28/2011 RAIDFILE.CONF(5)