04-13-2011
first thank u for help
we have tried and leave the server without power for more than 30 s
and we are wondering if the nvram (openboot prom) is damaged, or is the system controller card has a problem
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I had Win98 and Win Xp on a dual boot on my system, I formatted my C: drive to get rid of Win98 and installed Linux Madrake in its Place, it all installed ok but when I boot up I can no longer dual boot and it goes straight into Mandrake Linux. How can I get either a dual boot so I can get to XP... (10 Replies)
Discussion started by: Merv
10 Replies
2. UNIX for Advanced & Expert Users
we have a problem with a server UNIX SUN OS 5.7 :
we tried to reboot it and we have the following error message :
"boot load failed
the file just loaded does not appear to be executable "
we booted the server in single user mode with the cdrom
we made the mirrored disk bootable
we tried... (2 Replies)
Discussion started by: farzolito
2 Replies
3. UNIX for Dummies Questions & Answers
i have instaled a boot loader and win98 on drive c: and linux on drive d: and when i go to boot with the loader into linux nottin happens.is there some way i should install lilo to let it boot of a loader on drive c: ? (5 Replies)
Discussion started by: perleo
5 Replies
4. UNIX for Advanced & Expert Users
Hi All.
Yesterday my pc worked fine. Today when booting the sequence gets just past mounting the root filesystem - it then says
' Module dependencies up to date (no new kernel modules found).'
At this point it hangs and goes no further! Does this sound familiar to anyone?
I am running... (2 Replies)
Discussion started by: silvaman
2 Replies
5. Solaris
When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error.
cannot find mis/krtld
boot error loading... (0 Replies)
Discussion started by: johncy_j
0 Replies
6. AIX
Hi Guys
everyone know this problem on P595???
One of my servers, on boot, sleep 10-15 minute on led 0c33.
I know that it's a console problem... but i don't understand how resolve it.
Ideas???
P.S.
Sorry for my english.
Thanks.
Zio (0 Replies)
Discussion started by: Zio Bill
0 Replies
7. Solaris
Hi everyone,
I have sun fire280R machine before i it is installed with solaris5.9 now i want to upgrade it but it not booting from the cd rom ....OK prompt also not comming i dont have solaris keyboard to press stop-A key...i have a intel supported keyboard ...what may be the problem it is... (1 Reply)
Discussion started by: alakshmanrao
1 Replies
8. UNIX for Dummies Questions & Answers
hello
i have a sun server V890 and it stops booting after adding 2 CPUs modules and gives me the following error message:
Enabling system bus....... Done
Initializing CPUs......... Done
Initializing boot memory..
RAM-Copy CRC failure!Can't start: No image found
FATAL: Can't find/decompress... (0 Replies)
Discussion started by: bahjatm
0 Replies
9. Solaris
Hi all,
I have the the following SCSI diagnostic codes shown in the attached photo
I suspect disk drive failure what can I do further to diagnose the disk. and if possible to boot into OS again. (5 Replies)
Discussion started by: h@foorsa.biz
5 Replies
10. Red Hat
Hi,
My HP machine is using as boot device a disk defined in the Storage (IBM V5000). The connection is done by fiber connected through fiber switch.
No lacal disks are installed.
I'm using redhat 6.6.
I've installed and configured multipath.
Everything seems to work properly, however,... (0 Replies)
Discussion started by: Pazzeo
0 Replies
CHCPU(8) User Manuals CHCPU(8)
NAME
chcpu - configure CPUs
SYNOPSIS
chcpu [-e] [-d] [-c] [-g] cpu-list
chcpu [-p] mode
chcpu -r
chcpu [-h] [-V]
DESCRIPTION
chcpu can modify the state of CPUs. It can enable or disable CPUs, scan for new CPUs, change the CPU dispatching mode of the underlying
hypervisor, and request CPUs from the hypervisor (configure) or return CPUs to the hypervisor (deconfigure).
Some options have a cpu-list argument. Use this argument to specify a comma-separated list of CPUs. The list can contain individual CPU
addresses or ranges of addresses. For example, 0,5,7,9-11 makes the command applicable to the CPUs with the addresses 0, 5, 7, 9, 10, and
11.
OPTIONS
-r, --rescan
Trigger a rescan of CPUs. Use this option on systems that do not automatically detect newly attached CPUs. The Linux kernel then
recognizes the new CPUs.
-c, --configure cpu-list
Configure all specified CPUs. Configuring a CPU means that the hypervisor takes a CPU from the CPU pool and assigns it to the vir-
tual hardware on which your kernel runs.
-e, --enable cpu-list
Enable all specified CPUs. Enabling a CPU means that the kernel sets it online. A CPU must be configured, see -c, before it can be
enabled.
-p, --dispatch mode
Set the CPU dispatching mode (polarization). This option has an effect only if your hardware architecture and hypervisor support
CPU polarization. Available modes are:
horizontal The workload is spread across all available CPUs.
vertical The workload is concentrated on few CPUs.
-d, --disable cpu-list
Disable all specified CPUs. Disabling a CPU means that the kernel sets it offline.
-g, --deconfigure cpu-list
Deconfigure all specified CPUs. Deconfiguring a CPU means that the hypervisor removes the CPU from the virtual hardware on which
the Linux instance runs and returns it to the CPU pool. A CPU must be offline, see -d, before it can be deconfigured.
-h, --help
Display help information and exit.
-V, --version
Display version information and exit.
AUTHOR
Heiko Carstens <heiko.carstens@de.ibm.com>
COPYRIGHT
Copyright IBM Corp. 2011
SEE ALSO
lscpu(1)
AVAILABILITY
The chcpu command is part of the util-linux package and is available from Linux Kernel Archive <ftp://ftp.kernel.org/pub/linux/utils/util-
linux/>.
Linux June 2012 CHCPU(8)