04-13-2011
please try a complete powercycle (pull the power-cords and wait 30 seconds...) of the system.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I had Win98 and Win Xp on a dual boot on my system, I formatted my C: drive to get rid of Win98 and installed Linux Madrake in its Place, it all installed ok but when I boot up I can no longer dual boot and it goes straight into Mandrake Linux. How can I get either a dual boot so I can get to XP... (10 Replies)
Discussion started by: Merv
10 Replies
2. UNIX for Advanced & Expert Users
we have a problem with a server UNIX SUN OS 5.7 :
we tried to reboot it and we have the following error message :
"boot load failed
the file just loaded does not appear to be executable "
we booted the server in single user mode with the cdrom
we made the mirrored disk bootable
we tried... (2 Replies)
Discussion started by: farzolito
2 Replies
3. UNIX for Dummies Questions & Answers
i have instaled a boot loader and win98 on drive c: and linux on drive d: and when i go to boot with the loader into linux nottin happens.is there some way i should install lilo to let it boot of a loader on drive c: ? (5 Replies)
Discussion started by: perleo
5 Replies
4. UNIX for Advanced & Expert Users
Hi All.
Yesterday my pc worked fine. Today when booting the sequence gets just past mounting the root filesystem - it then says
' Module dependencies up to date (no new kernel modules found).'
At this point it hangs and goes no further! Does this sound familiar to anyone?
I am running... (2 Replies)
Discussion started by: silvaman
2 Replies
5. Solaris
When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error.
cannot find mis/krtld
boot error loading... (0 Replies)
Discussion started by: johncy_j
0 Replies
6. AIX
Hi Guys
everyone know this problem on P595???
One of my servers, on boot, sleep 10-15 minute on led 0c33.
I know that it's a console problem... but i don't understand how resolve it.
Ideas???
P.S.
Sorry for my english.
Thanks.
Zio (0 Replies)
Discussion started by: Zio Bill
0 Replies
7. Solaris
Hi everyone,
I have sun fire280R machine before i it is installed with solaris5.9 now i want to upgrade it but it not booting from the cd rom ....OK prompt also not comming i dont have solaris keyboard to press stop-A key...i have a intel supported keyboard ...what may be the problem it is... (1 Reply)
Discussion started by: alakshmanrao
1 Replies
8. UNIX for Dummies Questions & Answers
hello
i have a sun server V890 and it stops booting after adding 2 CPUs modules and gives me the following error message:
Enabling system bus....... Done
Initializing CPUs......... Done
Initializing boot memory..
RAM-Copy CRC failure!Can't start: No image found
FATAL: Can't find/decompress... (0 Replies)
Discussion started by: bahjatm
0 Replies
9. Solaris
Hi all,
I have the the following SCSI diagnostic codes shown in the attached photo
I suspect disk drive failure what can I do further to diagnose the disk. and if possible to boot into OS again. (5 Replies)
Discussion started by: h@foorsa.biz
5 Replies
10. Red Hat
Hi,
My HP machine is using as boot device a disk defined in the Storage (IBM V5000). The connection is done by fiber connected through fiber switch.
No lacal disks are installed.
I'm using redhat 6.6.
I've installed and configured multipath.
Everything seems to work properly, however,... (0 Replies)
Discussion started by: Pazzeo
0 Replies
psradm(8) System Manager's Manual psradm(8)
NAME
psradm, offline, online - Stops and starts processors in a multiprocessor system
SYNOPSIS
/usr/sbin/psradm -f [-v] [[-a] [processor_id...]]
/usr/sbin/psradm -n [-v] [[-a] [processor_id...]]
/usr/sbin/online [-v] [processor_id...]
/usr/sbin/offline [-v] [processor_id...]
OPTIONS
The following options apply only to the psradm command: Specifies that all the processors except the master processor be put off line or on
line. Puts the specified processor off line. Puts the specified processor on line.
The following option applies to all forms of the command: Displays a message about the status of the operation performed on each processor.
DESCRIPTION
On a multiprocessor system, the psradm command puts one or more processors off line (stops a processor) or on line (starts a processor).
The processor_id variable specifies an integer that uniquely identifies a processor. Use the psrinfo command to display processor identi-
fication numbers.
The offline command puts one or more processors off line (stops a processor). If no processors are specified, all processors that are on
line are stopped except the master processor.
The online command puts one or more processors on line (starts a processor). If no processors are specified, all processors that are off
line are started.
Note that you cannot use these commands to start or stop the master processor in a multiprocessor system.
You must be the root user to use this command.
The /var/adm/wtmp file contains information about successful processor state transitions.
RESTRICTION
Do not use the psradm command to disable CPUs when benchmarking performance, because the command does not provide an accurate reflection of
the performance of a system that actually has fewer CPUs. Accurate performance results are obtained only when you disable the CPUs at the
SRM console command level.
EXAMPLES
The following command puts processors 2 and 3 off line: # psradm -f 2 3 The following command puts all the processors on line: # psradm -n
-a The following command puts all processors on line: # online -v
FILES
SEE ALSO
Commands: pset_info(1), psrinfo(1)
Files: processor_sets(4)
psradm(8)