04-11-2011
It looks like the new disk was added to the pool (zpool add ...) instead of being set as a replacement disk (zpool replace ...).
I'm afraid you'll have to rebuild the whole pool from scratch (backup/restore) to get back the original layout.
8 More Discussions You Might Find Interesting
1. HP-UX
Is it possible to create the CDROM device file for a drive attached to the parallel port? I have a removable CDROM drive (gift - I'm trying not to return it, but may have to anyways) that attaches via parallel port. The only device that I can attach to that hardware address is /dev/c1t0d0_lp, a... (9 Replies)
Discussion started by: LivinFree
9 Replies
2. Solaris
Is it possible to create a Mirror with zfs ??
I'm experimented user with Solstice Disk suite.
Or Sun Volume manager or veritas volume manager.
But, i would like switch from Disksuite to Zfs.
All my mirrored disks. (1 Reply)
Discussion started by: simquest
1 Replies
3. UNIX for Dummies Questions & Answers
I am having trouble understanding the difference between a passthrough device and a named device and when you would use one or the other to access equipment.
As an example, we have a tape library and giving the command
"camcontrol devlist" gives the following output:
akx# camcontrol... (1 Reply)
Discussion started by: thumper
1 Replies
4. Solaris
I've looked a little but haven't found a solid answer, assuming there is one.
What's better, hardware mirroring or ZFS mirroring? Common practice for us was to use the raid controllers on the Sun x86 servers. Now we've been using ZFS mirroring since U6. Any performance difference? Any other... (3 Replies)
Discussion started by: Lespaul20
3 Replies
5. Solaris
Hi ,
I am new to SVM .when i try to learn RAID 1 , first they are creating two RAID 0 strips through
metainit d51 1 1 c0t0d0s2
metainit d52 1 1 c1t0d0s2
In the next step
metainit d50 -m d51
d50: Mirror is setup
next step is
metaattach d50 d52
d50 : submirror d52 is... (7 Replies)
Discussion started by: vr_mari
7 Replies
6. HP-UX
what is the difference between DRD and Root Mirror Disk using LVM mirror ? (3 Replies)
Discussion started by: maxim42
3 Replies
7. Solaris
Hi,
I have Solaris-10 (release-7) box without any non global zone. I have a very critical change after couple of days from application side. For safer side, we want to keep few level of backups just in case of faliure. This server is having three pool
root@prod_ddoa01:/# zpool list
NAME SIZE... (2 Replies)
Discussion started by: solaris_1977
2 Replies
8. Solaris
Hello,
I am upgrading Veritas from 5.1 to 6.0.1/6.0.5 in a Solaris 10 u8 server with OS mirrored (rpool) in zfs/zpool configuration.
I need to split it to have a quick way to backout in case of failure (make splitted mirror side bootable for a quick revert, like booting from it). I remember... (3 Replies)
Discussion started by: feroccimx
3 Replies
LEARN ABOUT DEBIAN
dpm-addfs
DPM-ADDFS(1) DPM Administrator Commands DPM-ADDFS(1)
NAME
dpm-addfs - add a filesystem to a disk pool
SYNOPSIS
dpm-addfs --poolname pool_name --server fs_server --fs fs_name [ --st status ] [ --weight weight ] [ --help ]
DESCRIPTION
dpm-addfs adds a filesystem to a disk pool.
This command requires ADMIN privilege.
OPTIONS
pool_name
specifies the disk pool name previously defined using dpm-addpool.
server specifies the host name of the disk server where this filesystem is mounted.
fs specifies the mount point of the dedicated filesystem.
status Initial status of this filesystem. It can be set to 0 or DISABLED or RDONLY. This can be either alphanumeric or the corresponding
numeric value.
weight specifies the weight of the filesystem. This is used during the filesystem selection. The value must be positive. It is recommended
to use a value lower than 10. Default is 1.
EXAMPLE
dpm-addfs --poolname Volatile --server sehost --fs /data
EXIT STATUS
This program returns 0 if the operation was successful or >0 if the operation failed.
SEE ALSO
dpm(1), dpm_addfs(3), dpm-addpool(1)
LCG
$Date$ DPM-ADDFS(1)