hi,
i m tryin to learn ldap.
but its not getting configured.
the error msg it shows is:
LDAP configure error: BDB/HDB : Berkeley DB version incompatibe.
The BDB version i have installed is bdb4.2.52 and the ldap version is openldap-2.3.12.
my machine is running on red hat linux 9.
Why... (1 Reply)
Hi Gurus:)
I have to connect from a SunOS 5.10 to a 5.8 using sftp in BatchMode. For this, I have generated a Public-Key (ssh-keygen -b 1024 -P "" -t dsa) on the 5.10 and saved it in ~remote-user/.ssh/authorized-keys on the 5.8.
Then, running either one of ssh or sftp, it asks for the... (24 Replies)
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help :( (7 Replies)
Following this thread :
https://www.unix.com/hp-ux/189023-solved-way-tell-printer-used-configured-print-queue.html
This is rwuerth's nice contribution!
I had a more complicated script written a long time ago to find out this information,
but after realizing due to VBE's post (thank you VBE)... (0 Replies)
Hi all,
I have an environment with Aix and Linux severs zoned to tape drives
I'd like to list HBAs WWN on my servers which are zoned to the drives.
Thanks (1 Reply)
Hi have a solaris server with the following IP 192.168.0.85, but anybody can login in using 172.19.0.85, and the ifconfigcommand does not show the 172.19.05 .
# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask... (6 Replies)
I have kali running on vbox as :-
/etc/network/interfaces
ifup eth0 gives me
tpcdump (0 Replies)
Discussion started by: lazerz
0 Replies
LEARN ABOUT CENTOS
rescan-scsi-bus.sh
RESCAN-SCSI-BUS.SH(1) User Commands RESCAN-SCSI-BUS.SH(1)NAME
rescan-scsi-bus.sh - script for adding and removing SCSI devices without rebooting
SYNOPSIS
rescan-scsi-bus.sh [options] [host [host ...]]
OPTIONS -a, --alltargets
scan all targets, not just currently existing [default: disabled]
-d enable debug [default: 0]
-l activates scanning for LUNs 0--7 [default: 0]
-L NUM activates scanning for LUNs 0--NUM [default: 0]
-w, --wide
scan for target device IDs 0--15 [default: 0--7]
-c enables scanning of channels 0 1 [default: 0 / all detected ones]
-r, --remove
enables removing of devices [default: disabled]
-f, --flush
flush failed multipath devices [default: disabled]
-i, --issue-lip
issue a FibreChannel LIP reset [default: disabled]
-u, --update
look for existing disks that have been remapped
-s, --resize
look for resized disks and reload associated multipath devices, if applicable
--forcerescan
rescan existing devices
--forceremove
remove and readd every device (DANGEROUS)
--nooptscan
don't stop looking for LUNs is 0 is not found
--color
use coloured prefixes OLD/NEW/DEL
--hosts=LIST
scan only host(s) in LIST
--channels=LIST
scan only channel(s) in LIST
--ids=LIST
scan only target ID(s) in LIST
--luns=LIST
scan only lun(s) in LIST
--sync, --nosync
issue a sync / no sync [default: sync if remove]
--attachpq3
tell kernel to attach sg to LUN 0 that reports PQ=3
--reportlun2
tell kernel to try REPORT_LUN even on SCSI2 devices
--largelun
tell kernel to support LUNs > 7 even on SCSI2 devs
--sparselun
tell kernel to support sparse LUN numbering
Host numbers may thus be specified either directly on cmd line (deprecated) or or with the --hosts=LIST parameter (recommended).
LIST: A[-B][,C[-D]]... is a comma separated list of single values and ranges (No spaces allowed.)
SEE ALSO
rescan-scsi-bus.sh Homepage: http://www.garloff.de/kurt/linux/#rescan-scsi
sg3_utils Homepage: http://sg.danny.cz/sg
rescan-scsi-bus.sh 1.57 leden 2014 RESCAN-SCSI-BUS.SH(1)