04-05-2011
Thanks for your help. I am currently formatting the partition. Will setup the file system next.
8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I need help in the form of the complete procedures necessary in setting up an Apache web server on a Sun Sparc running Solaris 8
David Johnston
P.S New to the Unix arena (1 Reply)
Discussion started by: David Johnston
1 Replies
2. Solaris
A sparc server has a new SCSI hard disk added and labeled by the engineer, but they need to be formatted identically to an existing disk (c4t0d0). You decide to script the process and run from the command line without interaction.
I know that the following command line must be achieve this.
#... (3 Replies)
Discussion started by: kingsan
3 Replies
3. Solaris
Hello,
Running a Sun Solaris 9 E250 and need advice or suggestions on what type of external hard disks are compatible and or available. It's an old machine and is due for replacement soon but in the short term need an external hard drive for backup etc as the partner/backup machine has just... (2 Replies)
Discussion started by: KenLynch
2 Replies
4. Filesystems, Disks and Memory
Folks;
I just added 2 physical new hard drives to my SUSE server. My server is already running SUSE 10.3 version.
Is there a command i can use to add the new space or even see if the system can sees them? (3 Replies)
Discussion started by: Katkota
3 Replies
5. Solaris
Hi all,
I have application running on sun server T5440 4x8x1.4 GHz, 64 GB RAM, application running very slow though load average too low. when I install my application on another server SUN M3000 (One CPU 1x8x2.5GHz, 8GB RAM), application run smoothly.
Here is my server T5440 info:
... (6 Replies)
Discussion started by: insatiable1610
6 Replies
6. Solaris
show /HOST command shows that
status = OpenBoot Running
when in this state, can the power be unplugged from the server ?
we are unable to bring the status to "powered off". Even if we issue "stop /SYS" it will momentarily be in the powered off status and then go back to power on... (1 Reply)
Discussion started by: paulk93
1 Replies
7. Solaris
SPARC Enterprise T5440 Server, can not power off
I connect to Service Processor via serial port and submit the following to boot the system, it boots fine but can not power off the system. Can someone help?
The following takes me to unix login
-> start /SYS
-> start /SP/console... (6 Replies)
Discussion started by: paulk93
6 Replies
8. Solaris
Hi,
I have two SCSI Hard Drives in a Sun Solaris 8 server as shown below. I would like to access Disk1 and look at its contents, directory structure and files. How do I change my default directory from Disk 0 to Disk 1 and vice versa?
Thank you. (5 Replies)
Discussion started by: ssabet
5 Replies
LEARN ABOUT MINIX
repartit
REPARTITION(8) System Manager's Manual REPARTITION(8)
NAME
repartition - load a partition table
SYNOPSIS
repartition device [partition-file]
DESCRIPTION
Repartition uploads a new partition table for the partitions of device. The table is obtained from the first sector of partition-file if
given, device otherwise. Device may refer to the whole drive or a primary partition, depending on whether you want to upload a partition
or a subpartition table. The partitions will be truncated to fit within the enclosing device like the disk driver does, unless the numbers
are coming from partition-file.
EXAMPLES
repartition /dev/hd0
repartition /dev/hd4 /etc/hd4.table
Reload the partition table of drive 0 setting /dev/hd[1-4], and the subpartition table of /dev/hd4 setting /dev/hd4[a-d] using a file. The
latter may be useful if you need more than the 4 subpartitions a single Minix partition gives you.
DIAGNOSTICS
The new table is printed on standard output.
FILES
/dev/hd[0-9]
SEE ALSO
hd(4), part(8).
BUGS
The disk must be in use for the changes to stick. The partition table of an idle disk will be reloaded on the first open.
AUTHOR
Kees J. Bot (kjb@cs.vu.nl)
REPARTITION(8)