Sponsored Content
Operating Systems AIX EtherChannel interface ping pelicularity Post 302511005 by thenomad on Tuesday 5th of April 2011 01:32:12 PM
Old 04-05-2011
Quote:
Originally Posted by kah00na
We had similar issues with a different product. Eventually, we quit using it because of similar reasons and also because sometimes our boxes would ping, but would be froze up somehow and not respond to login attempts. Now have our NIM server SSH to every box every 15 minutes and run a "/usr/bin/ls" command and check that the return code was "0". One of our other boxes does an SSH to our NIM server to make sure it is running. We have to monitor the monitor. Smilie
Very novel idea and I used similar structs in the past. But this time, nagios monitoring is what we are sticking to for simplifying the operations staff's work. So, I have to get this one fixed such that if a ping request comes, only one of the interfaces in an etherchannel should respond, not both.
 

9 More Discussions You Might Find Interesting

1. AIX

Problem with Etherchannel

I'm trying to configure Etherchannel on AIX 5.3 and I'm having some problems. I am aggregating both of the onboard NIC's (ent0 and ent1) into a new adapter ent2 for failover reasons obviously. At first I was experiencing a problem where about 50% of all my packets would be dropped. Then after... (4 Replies)
Discussion started by: acascianelli
4 Replies

2. AIX

AIX / Etherchannel / VLANs

I have 1 AIX server, 4 dual ported fiber attached ethernet cards and 4 VLANS coming in. Is it possible to present those 8 ports as 1 IP address using etherchannel? Thanks. (5 Replies)
Discussion started by: jwholey
5 Replies

3. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies

4. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies

5. AIX

Can EtherChannel be a redundancy config?

I have one p5 server, no lpar, 2 physical network adapter, bundle as one EtherChannel. The two 2 physical network adapter connect to 2 network switches. How to make this as a redundancy config? Current is if one physical network adapter down, the seond one will go through the network. but if... (2 Replies)
Discussion started by: rainbow_bean
2 Replies

6. AIX

Aggregated Etherchannel

Hi, I have a AIX5.3 P6-520 with 8x1Gb Ethernet ports with possible connections to 2 CISCO 2960 switches. I can create 8023ad Etherchannels which work correctly with the switches (I have set up for LACP passive and a valid channels) But can create 2x 8023ad 4Gb Etherchannels with no backups.... (2 Replies)
Discussion started by: spitzie
2 Replies

7. IP Networking

Linux load balancer ping redirect to other interface

Im configuring centos with load balance with ip route and ip rule Eth0 192.168.1.5 Eth1 192.168.5.128 # ip route 192.168.5.0/24 dev eth1 scope link src 192.168.5.128 192.168.1.0/24 dev eth0 proto kernel scope link src 192.168.1.5 169.254.0.0/16 dev eth1 scope link # ip route show... (2 Replies)
Discussion started by: hadinetcat
2 Replies

8. AIX

Etherchannel failover testing

Hi Guys, I am trying to test an etherchannel failover and switchback. I did failover from primary to backup adapter, but now I am not able to switch it back to primary. phcxxxxx:/ > entstat -d ent4 | grep Active Active channel: backup adapter ... (1 Reply)
Discussion started by: snchaudhari2
1 Replies

9. AIX

PowerVM SEA etherchannel performance ?

Hello, POWER7 machine. 4 x 1Gbit port ethernet adapter is dedicated to vios. 8023ad etherchannel is created using those 4 ports. Etherchannel adapter is shared to lpars using SEA. If I test network performance directly from vios partition (using iperf) I'm geting nice 4Gbit throughput. But if... (3 Replies)
Discussion started by: vilius
3 Replies
OCF_PACEMAKER_PINGD(7)					      Pacemaker Configuration					    OCF_PACEMAKER_PINGD(7)

NAME
ocf_pacemaker_pingd - pingd resource agent SYNOPSIS
[OCF_RESKEY_pidfile=string] [OCF_RESKEY_user=string] [OCF_RESKEY_dampen=integer] [OCF_RESKEY_set=string] [OCF_RESKEY_name=string] [OCF_RESKEY_section=string] [OCF_RESKEY_multiplier=integer] [OCF_RESKEY_host_list=string] [OCF_RESKEY_interval=integer] [OCF_RESKEY_attempts=integer] [OCF_RESKEY_timeout=integer] [OCF_RESKEY_options=string] pingd [start | stop | monitor | meta-data | validate-all] DESCRIPTION
This agent (ocf:pacemaker:pingd) has been replaced by the more reliable ocf:pacemaker:ping. It records (in the CIB) the current number of ping nodes (specified in the 'host_list' parameter) a cluster node can connect to. SUPPORTED PARAMETERS
OCF_RESKEY_pidfile = string [/pingd-] PID file OCF_RESKEY_user = string [root] The user we want to run pingd as The user we want to run pingd as OCF_RESKEY_dampen = integer [5s] Dampening interval The time to wait (dampening) further changes occur OCF_RESKEY_set = string [] Set name The name of the instance_attributes set to place the value in. Rarely needs to be specified. OCF_RESKEY_name = string [pingd] Attribute name The name of the attributes to set. This is the name to be used in the constraints. OCF_RESKEY_section = string [] Section name The section place the value in. Rarely needs to be specified. OCF_RESKEY_multiplier = integer [] Value multiplier The number by which to multiply the number of connected ping nodes by OCF_RESKEY_host_list = string [] Host list The list of ping nodes to count. Defaults to all configured ping nodes. Rarely needs to be specified. OCF_RESKEY_interval = integer [1] ping interval in seconds How often, in seconds, to check for node liveliness OCF_RESKEY_attempts = integer [2] no. of ping attempts Number of ping attempts, per host, before declaring it dead OCF_RESKEY_timeout = integer [2] ping timeout in seconds How long, in seconds, to wait before declaring a ping lost OCF_RESKEY_options = string [] Extra Options A catch all for any other options that need to be passed to pingd. AUTHOR
Andrew Beekhof <andrew@beekhof.net> Author. Pacemaker Configuration 06/10/2014 OCF_PACEMAKER_PINGD(7)
All times are GMT -4. The time now is 05:46 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy