Sponsored Content
Top Forums UNIX for Dummies Questions & Answers sleep command off by a second Post 302510679 by Scott on Monday 4th of April 2011 04:15:08 PM
Old 04-04-2011
expr is also very inefficient (if every millisecond is a prisoner Smilie).

Code:
$ cat exprTest
count=1000

counter=0
printf "With expr, Start: "
date
while [ $counter -le $count ]; do
  counter=`expr $counter + 1`
done
printf "With expr, End:   "
date
echo $counter

counter=0
printf "Without expr, Start: "
date
while [ $counter -le $count ]; do
  ((counter++))
done
printf "Without expr, End:   "
date
echo $counter


$ ./exprTest
With expr, Start: Mon  4 Apr 2011 22:13:59 CEST
With expr, End:   Mon  4 Apr 2011 22:14:01 CEST
1001
Without expr, Start: Mon  4 Apr 2011 22:14:01 CEST
Without expr, End:   Mon  4 Apr 2011 22:14:01 CEST
1001

 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

How can I get a command to sleep < 1 second?

I am running a number of processes through a kill -15 loop as a temporary fix to some viscious memory leaks. I cannot pass the entire list of processes through the kill at once, because the nature of the monitoring my client has will cause the software to failover. Because of the large number of... (1 Reply)
Discussion started by: mattd
1 Replies

2. UNIX for Dummies Questions & Answers

sleep command

If I give sleep(50) what does it mean? My program waits for further execution or all my other processes wait? (3 Replies)
Discussion started by: leewar
3 Replies

3. Shell Programming and Scripting

Sleep Command

I am in need of some help; think I have confused myself. Here is the issue I am faced with. The script log file was fine, the nohup.out file has tens of thousands of lines like illegal use of sleep: sleep seconds So I assume there is something with the seconds calculation in the script... (1 Reply)
Discussion started by: Glove
1 Replies

4. UNIX for Dummies Questions & Answers

sleep command

Hi All I have a requiremnt to run a script inside another script. here i am pulling the record count from the table in oracle.If record count is greater than 0 the script is executed.The scripts updates the count in the table and again the count is found out and the condition is checked and same... (3 Replies)
Discussion started by: dr46014
3 Replies

5. Shell Programming and Scripting

sleep command

Hi, Did the sleep command work for hours or only minutes just give description to work on my script waiting for the earliest response (5 Replies)
Discussion started by: thelakbe
5 Replies

6. UNIX for Dummies Questions & Answers

Help with sleep command

sleep 10 & Is this the write line of command to suspend 5 jobs for 10 minutes (6 Replies)
Discussion started by: senyor17
6 Replies

7. Shell Programming and Scripting

Sleep command

Hi All, i am very new to shall script . i am not that much aware of sleep command , i want to terminate the sleep command after certain time. following is my code. while loop sleep 1800 messag=/status.sql donethe script will be on sleep untill the messag be comes P. here my requirement... (4 Replies)
Discussion started by: mandlysreedhar
4 Replies

8. Shell Programming and Scripting

Sleep Command

Hello, Need a little help with the script below. I can't get it to sleep :( I'm trying to get this to check if the process is running and if it is, wait 10 secs and check again. Keep doing this until it's not running and then stop checking and send the email. #!/bin/ksh mailto=`cat... (2 Replies)
Discussion started by: bbbngowc
2 Replies

9. Shell Programming and Scripting

Help with sleep command:

Hi Frnz, I need to execute sleep command but i dont know the definite time. Let me put my req: I am running one shell script and this script creates some lock file in temp dir ...now in my script i want one function to go into sleep mode till this lock file exists..one lock file gone that... (6 Replies)
Discussion started by: gnnsprapa
6 Replies

10. Shell Programming and Scripting

Sleep command

I need help in script. I want my one script execute every time at 6:30 am and i have no cron access. So i am putting sleep command there , Script may took half an hour 35 min , it depend upon queries how much it take time, but that is not issue, So i want according to stop time of... (15 Replies)
Discussion started by: pallvi_mahajan
15 Replies
expr(1) 						      General Commands Manual							   expr(1)

Name
       expr - evaluate expressions

Syntax
       expr arg...

Description
       The arguments are taken as an expression.  After evaluation, the result is written on the standard output.  Each token of the expression is
       a separate argument.

       The operators and keywords are listed below.  The list is in order of increasing precedence, with equal precedence operators grouped.

       expr | expr	   Yields the first expr if it is neither null nor 0.  Otherwise yields the second expr.

       expr & expr	   Yields the first expr if neither expr is null or 0.	Otherwise yields 0.

       expr relop expr	   The relop is one of < <= = != >= > and yields 1 if the indicated comparison is true, '0' if false.  The  comparison	is
			   numeric if both expr are integers, otherwise lexicographic.

       expr + expr
	    expr - expr
			   Yields addition or subtraction of the arguments.

       expr * expr
	    expr / expr
	    expr % expr
			   Yields multiplication, division, or remainder of the arguments.

       expr : expr	   The	matching  operator compares the string first argument with the regular expression second argument; regular expres-
			   sion syntax is the same as that of The (...) pattern symbols can be used to select a portion of the  first  argument.
			   Otherwise, the matching operator yields the number of characters matched ('0' on failure).

       ( expr ) 	   parentheses for grouping.

Examples
       The first example adds 1 to the Shell variable a:
       a=`expr $a + 1`
       The second example finds the file name part (least significant part) of the pathname stored in variable a,
       expr $a : '.*/(.*)' '|' $a
       Note the quoted Shell metacharacters.

Diagnostics
       The command returns the following exit codes:

       0    The expression is neither null nor '0'.

       1    The expression is null or '0'.

       2    The expression is invalid.

See Also
       ed(1), sh(1), test(1)

																	   expr(1)
All times are GMT -4. The time now is 08:40 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy