03-31-2011
Manoj,
Try scsi_id or cat the /proc/scsi which should reveal you the required details.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
How can you get a scsi card to initalize or decome available at boot up on AIX 4.3 (1 Reply)
Discussion started by: truma1
1 Replies
2. UNIX for Advanced & Expert Users
can any one tell me what's the difference between scsi and differential scsi? (2 Replies)
Discussion started by: i2admin
2 Replies
3. UNIX for Advanced & Expert Users
I would like to install a AIT drive to the scsi connector on our solaris box. I am very new to the unix world and would be greatful if someone could help or lead me in the right direction.
Thanks (4 Replies)
Discussion started by: vpyle
4 Replies
4. Solaris
Hi. I need to find a simple SCSI adapter card for a Sun Ultra 5 workstation. I don't need the type w/ ethernet attached (e.g. X1032) as I already have ethernet onboard & they are more spendy.
I know Adaptec is out, but what unit would work? I am attaching an external SCSI tape unit to this... (4 Replies)
Discussion started by: Plain Person
4 Replies
5. Solaris
I have run init 0 to bring it to OK prompt.
I know that probe-scsi-all can hang the system.
I want to know what is the difference between probe-scsi-all and probe-scsi.
I was told that probe-scsi-all external and internal devices and probe-scsi shows only internal devices. what dose this ... (3 Replies)
Discussion started by: nitinkgoud
3 Replies
6. UNIX for Dummies Questions & Answers
hey guys this is my problem I have SCO unix installed on a IDE h/drive. I want to add a SCSI hard drive, how do i do that within UNIX (1 Reply)
Discussion started by: kwame.neilsen
1 Replies
7. Shell Programming and Scripting
Hi,
I have a challenging task,in which i have to find the duplicate files by its name and size,then i need to take anyone of the file.Then i need to open the file and find for more than one pattern and count of that pattern.
Note:These are the samples of two files,but i can have more... (2 Replies)
Discussion started by: jerome Sukumar
2 Replies
8. UNIX for Advanced & Expert Users
how can i determine what disks are scsi disks from the format command? (5 Replies)
Discussion started by: rcon1
5 Replies
9. Filesystems, Disks and Memory
Linux / Kernel experts,
Please help. I'm getting errors with various return codes, similar to:
kernel: SCSI error : <0 0 5 165> return code = 0x8000002
I would like to know how / where to lookup the definition of the numbers between the angle brackets, and the return code itself.
I... (3 Replies)
Discussion started by: bumblebee
3 Replies
10. Hardware
Hi i ahve a SCSI drive that it use to work but now is not working. The Sun machine can not read the drive. My question is there is any other way to get the data back from the SCSI drive? I think if i replace the chip board on teh SCSI drive it might help to just buy a new Board but there is any... (4 Replies)
Discussion started by: percel
4 Replies
SRAW(8) System Manager's Manual SRAW(8)
NAME
sraw - benchmark raw scsi I/O performance under linux
SYNOPSIS
sraw [ -fiv6 ] scsi-device [ bstart [ bstep ] ]
DESCRIPTION
This program basically reads the specified scsi device and measures the throughput. Note that the filesystem *AND* the buffer cache are
bypassed by this code, this program was designed to benchmark the naked scsi drivers by themselves without the need to account for the
overhead of any other portion of the kernel. It also could be used to benchmark disk read throughput.
This program does a series of reads of the disk, of consecutive areas on the disk. The device is first queried to determine the sector
size for the device, and then the series of reads is begun. About 5.0 Mb is read from the device, and then the performance numbers are
reported. Note that since the buffer cache is completely bypassed, there is no need to be concerned about cache hits or anything.
Output of sraw is a set of lines, 4 numbers per line: blocksize, elapsed time, nblocks and throughput (in bytes per second).
scsi-device is either a block device (e.g. /dev/sda, /dev/scd0) or a generic SCSI device (e.g. /dev/sg0).
OPTIONS
-f set FUA (Force Unit Access) bit during read. Data is then read from media instead of internal drive cache.
-i use legacy ioctl instead of new SG I/O layer (will not work on 2.6 kernel and block devices).
-v more verbose output.
-6 use 6-bytes instead of 10-bytes read command. In this case, only the first GB of data could be read from media.
bstart starting block to check different zones on ZBR discs
bstep factor for sequential stepping, default 1. Use 0 for reading always the same blocks (from cache)
ERRORS
sraw could issue input/output errors when reading too many blocks at the same time from a block device like /dev/sda. To get rid of them,
use /dev/sgN instead.
AUTHOR
sraw was first written by Eric Youngdale. Extensions (-v, -f, -6, SG IO, man page) were written by Eric Delaunay.
SEE ALSO
sg_dd(8) from sg3-utils package.
AVAILABILITY
sraw is available at
ftp://tsx-11.mit.edu/pub/linux/ALPHA/scsi/
Nov 1993 SRAW(8)