Sponsored Content
Full Discussion: RPCBIND Hang at Boot
Operating Systems Linux RPCBIND Hang at Boot Post 302508883 by andreaden on Tuesday 29th of March 2011 10:50:40 AM
Old 03-29-2011
RPCBIND Hang at Boot

Hi guys,

i explain my problem:

I've FC10 64bit installed on a server Dell R410.
When i boot the system with eth0 or eth1 linked (only one eth linked), all work fine and the system start normally.

When i boot the system with eth0 + eth1 linked,
the system hang when the rpcind service starting.
Nothing is possible..ssh, key pressure, ctrl-alt-canc,ping not response... only power off and restart.

I've tested this in Interactive boot.
With yes in prompt of interactive boot mode at rpcbind, status [OK] is visible but the system is freeze;


With no in interactive prompt boot, status of service is [FAILED] but the boot process go well.
In this case also nfs status is [FAILED].

I've tested with static ip or dhcp configuration of ethernet.

Any ideas what could be causing the boot failure?


thank's in advantage.
ps:sorry for my little english.
 

10 More Discussions You Might Find Interesting

1. SCO

rpcbind errors

HI, During the system bootup, following errors are being logged in "syslog" i) unix1 rpcbind: netdir_getbyname failed on tcp for host unix1, se rvice rpcbind ii)unix1 rpcbind: netdir_getbyname failed on udp for host unix1, se rvice rpcbind iii)unix1 in.snmpd: unix1: Host unknown. ... (0 Replies)
Discussion started by: tayyabq8
0 Replies

2. AIX

AIX 4.1.5/RS6000 boot hang, help requested

Hello there! I have a RS-6000 7043-140 machine with AIX version 4.1.5, that is working for almost 8 years now. It has a tty monitor. My problem started when I upgraded my machine to install a gxt250 graphics adapter card together with a 15" AOC VGA Monitor, logitech keyboard and mouse, ... (2 Replies)
Discussion started by: bright_genius
2 Replies

3. Solaris

solaris 5.8 hang on boot

I have an ultra 10 system, and am trying to install and verify a previously cloned hard drive, to make sure it works, that it really is a duplicate of the hard drive currently on an other server, etc. I plugged in this cloned hard drive as master, only drive in the system. No network LAN... (2 Replies)
Discussion started by: HikerLT
2 Replies

4. UNIX for Dummies Questions & Answers

NFS client subsystem hang up on boot

Hi, I have a Unix box running HP-UX 10.20 and it suddenly won't boot. Every time it goes down the boot checklist, it hangs on "NFS client subsystem" and just continues to say busy/wait. I have read something about the /etc/auto_master but don't quite understand what has to happen to fix it. ... (4 Replies)
Discussion started by: Asheley Ryan
4 Replies

5. Solaris

rpcbind failure

Hello experts.. What is the meaning of " RPC : rpcbind failure" in NFS ? What would be the reason for that? How can i resolve that issue? give me all aspects (all views).. Thanks in advance... (1 Reply)
Discussion started by: younus_syed
1 Replies

6. AIX

Boot from CD hang

Why is one of my blade hanging and does nothing after trying to boot from CD??? ================== I tried to press 1....JS20 does not support SMS menu Here's what I see after 30 minutes... ------------------------------------------------------------------------------- ... (0 Replies)
Discussion started by: mifch
0 Replies

7. SCO

Boot hang after relocate of LSI HBA controller

Hi folks, I had problems trying to install SCO OpenServer 6 on a PC with no floppy drive and a SATA CD drive. Eventually after advice received on this forum last week, I adopted a different approach by fitting the LSI HBA RAID adapter and associated disks into an older PC that does have CD and... (4 Replies)
Discussion started by: millosman
4 Replies

8. Ubuntu

NIS/RPCBind Conflict!

Hi I am trying to configure NIS client on my Ubuntu 12.04. But I could not put portmap without uninstalling rpcbind. Do I need to have rpcbind there on the server, or how can I have both portmap and rpcbind at same time there on the server, because it's having conflict. (1 Reply)
Discussion started by: nixhead
1 Replies

9. Red Hat

Boot process hang

Hello, Sometime i see that the boot process hangs. I am using rhel 6.2. At that time in the console i see Probing EDD (edd=off to disable)... SSH service seems to be started but i can't login... ssh logs (last lines) in verbose mode level 3: debug2: we did not send a packet,... (3 Replies)
Discussion started by: @dagio
3 Replies

10. Solaris

Rpcbind service not starting

Hello all, I have read just about every rpcbind not starting thread and article on the internet it seems, but I have not found a solution to my problem as of yet. I have a solaris 10 server that has been running with no problems for a while. The other day it crashed and would not boot to the gui... (2 Replies)
Discussion started by: Madrox72
2 Replies
Match-all classifier in tc(8)					       Linux					     Match-all classifier in tc(8)

NAME
matchall - traffic control filter that matches every packet SYNOPSIS
tc filter ... matchall [ skip_sw | skip_hw ] [ action ACTION_SPEC ] [ classid CLASSID ] DESCRIPTION
The matchall filter allows to classify every packet that flows on the port and run a action on it. OPTIONS
action ACTION_SPEC Apply an action from the generic actions framework on matching packets. classid CLASSID Push matching packets into the class identified by CLASSID. skip_sw Do not process filter by software. If hardware has no offload support for this filter, or TC offload is not enabled for the inter- face, operation will fail. skip_hw Do not process filter by hardware. EXAMPLES
To create ingress mirroring from port eth1 to port eth2: tc qdisc add dev eth1 handle ffff: ingress tc filter add dev eth1 parent ffff: matchall skip_sw action mirred egress mirror dev eth2 The first command creats an ingress qdisc with handle ffff: on device eth1 where the second command attaches a matchall filters on it that mirrors the packets to device eth2. To create egress mirroring from port eth1 to port eth2: tc qdisc add dev eth1 handle 1: root prio tc filter add dev eth1 parent 1: matchall skip_sw action mirred egress mirror dev eth2 The first command creats an egress qdisc with handle 1: that replaces the root qdisc on device eth1 where the second command attaches a matchall filters on it that mirrors the packets to device eth2. To sample one of every 100 packets flowing into interface eth0 to psample group 12: tc qdisc add dev eth0 handle ffff: ingress tc filter add dev eth0 parent ffff: matchall action sample rate 100 group 12 SEE ALSO
tc(8), iproute2 21 Oct 2015 Match-all classifier in tc(8)
All times are GMT -4. The time now is 09:35 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy