I need to insert a file called temp_impact (which has about 15 lines in it) to a file called 11.23cfg starting at line 33. I searched the forums and found the
sed '34i\
test' 11.23cfg > newfile
That will enter word test at the appropriate line, but i need the entire file dumped there. Any... (4 Replies)
Dear Folks :),
I am new to UNIX scripting and I do not know how can I insert some text in the first column of a UNIX text file at command promtp.
I can do this in vi editor by using this command :g/^/s//BBB_
e,g I have a file named as Test.dat and it containins below text:
michal... (4 Replies)
Hi all,
I need to insert new text and change existing text in a file. For that I used the below line in the command line and got the expected output.
sed '$a\
hi...
' shell > shell1
But I face problem when using the same in script. It is throwing the error as,
sed: command garbled:... (4 Replies)
Hello,
I'm new in Shell scripting but i should write a script, which inserts the license header out of a txt-File into the files in our Projekt. For the Java classes it runs without Problems but for XML files not. At xml-files i have to put the license Header after the xml-Header (?xml... (1 Reply)
I can't seem to get sed to allow me to insert text in the first line of an empty file. I have a file.txt that is a 0 byte file. I want sed to insert " fooBar" onto the first line. I've tried a few options and nothing seems to work. They work just fine if there's text in the file tho. Help? (4 Replies)
I have a test file that I want to read and insert only certain lines into the
the table based on a filter.
1. Rread the log file 12 Hours back Getdate() -12 Hours
2. Extract the following information on for lines that say "DUMP is
complete"
A. Date
B. Database Name
C.... (2 Replies)
Hi All,
I am using UNix Sun OS sun4u sparc SUNW,SPARC-Enterprise
My intention is to insert a line of text after 13th line of every file inside a particular directory.
While trying to do it for a single file , i am using sed
sed '3 i this is the 4th line' filename
sed: command garbled: 3... (5 Replies)
Discussion started by: gotamp
5 Replies
LEARN ABOUT DEBIAN
get-iab
GET-IAB(1) General Commands Manual GET-IAB(1)NAME
get-iab - Fetch the arp-scan IAB file from the IEEE website
SYNOPSIS
get-iab [options]
DESCRIPTION
get-iab fetches the Ethernet IAB file from the IEEE website, and saves it in the format used by arp-scan.
The IAB file contains all of the IABs (Individual Address Blocks) that have been registered with IEEE. Each IAB entry in the file speci-
fies the first 36-bits of the 48-bit Ethernet hardware address, leaving the remaining 12-bits for use by the registering organisation. For
example the IAB entry "0050C2003", registered to Microsoft, applies to any Ethernet hardware address from 00:50:c2:00:30:00 to
00:50:c2:00:3f:ff inclusive. Each IAB assignment represents a total of 2^12 (4,096) Ethernet addresses.
Major Ethernet hardware vendors typically use an OUI registration rather than an IAB registration. See get-oui(1) for details.
This script can be used to update the arp-scan IAB file from the latest data on the IEEE website. It is relatively rare to see Ethernet
addresses from IAB registrations, so the IAB file is not as important as the OUI file.
The IAB data is fetched from the URL http://standards.ieee.org/regauth/oui/iab.txt and the output file is saved to the file ieee-iab.txt in
the current directory. The URL to fetch the data from can be changed with the -u option, and the output file name can be changed with the
-f option.
The ieee-iab.txt file that is produced by this script is used by arp-scan to determine the Ethernet card vendor from its hardware address.
The directory that arp-scan will look for the ieee-iab.txt file depends on the options used when it was built. If it was built using the
default options, then it will look in /usr/local/share/arp-scan.
OPTIONS -h Display a brief usage message and exit.
-f <fn>
Write the output to the specified file instead of the default ieee-iab.txt.
-u <URL>
Use the specified URL to fetch the raw IAB data from instead of the default http://standards.ieee.org/regauth/oui/iab.txt
-v Display verbose progress messages.
FILES
ieee-iab.txt
The default output file.
EXAMPLES
$ get-iab -v
Renaming ieee-iab.txt to ieee-iab.txt.bak
Fetching IAB data from http://standards.ieee.org/regauth/oui/iab.txt
Fetched 230786 bytes
Opening output file ieee-iab.txt
1535 IAB entries written to file ieee-iab.txt
NOTES
get-iab is implemented in Perl, so you need to have the Perl interpreter installed on your system to use it.
get-iab uses the LWP::Simple Perl module to fetch the data from the IEEE website. You must have this module installed on your system for it
to work. This module is available on most distributions, often called libwww-perl. It is also available in source form from CPAN.
You can use a proxy server by defining the http_proxy environment variable.
AUTHOR
Roy Hills <Roy.Hills@nta-monitor.com>
SEE ALSO arp-scan(1)get-oui(1)arp-fingerprint(1)
http://www.nta-monitor.com/wiki/ The arp-scan wiki page.
March 30, 2007 GET-IAB(1)