03-25-2011
You could export using NFS..
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hello ! :confused:
Does anyone knows anything about procedure to convert Solaris UFS filesystem to VxFS.
Thx,
Witt (1 Reply)
Discussion started by: witt
1 Replies
2. Solaris
hi guys,
I am studying for the solaris scsa and i want to practice with ufsdump and restores, fssnaps etc...
my question is, i finally found a server with a tape drive attached that i can mess arouund with because its not a critical box.
its running solaris 8, and i want to do a ufsdump, but... (2 Replies)
Discussion started by: BG_JrAdmin
2 Replies
3. Solaris
How to find & replace bad disks in solaris & VXVM?plz
explain step by step? (2 Replies)
Discussion started by: xtreams
2 Replies
4. Solaris
what is the difference between VXVM and SVM ?
What is the advantages of VXVM over SVM ?
thanks (2 Replies)
Discussion started by: sijocg
2 Replies
5. UNIX for Advanced & Expert Users
Hi,
I have 2 hosts with Veritas VxVM and VxFS (5.0 MP3_RP2). I need to use the application filesystem's luns from these 2 hosts and mount it on another 2 hosts that are running Solaris 9 09/05 and SVM.
Is there resources online or has someone tried this? (0 Replies)
Discussion started by: xor
0 Replies
6. Solaris
Hi all,
How to i use vxfs for my server? Because when i install OS, it is installed with ufs, then after Solaris 10 installation, i proceed to install vxfs.
How do i convert all the ufs to vxfs? Or is it what i'm doing is the incorrect way?
Please help. :wall: (9 Replies)
Discussion started by: beginningDBA
9 Replies
7. Solaris
Hi All,
I have rootdg encapsulated within Veritas Volume Manager.
/# vxprint -vg rootdg
TY NAME ASSOC KSTATE LENGTH PLOFFS STATE TUTIL0 PUTIL0
v rootvol root ENABLED 24585216 - ACTIVE - -
v swapvol swap ENABLED 20484288 -... (3 Replies)
Discussion started by: solaris_1977
3 Replies
8. UNIX for Advanced & Expert Users
Hello,
Usually I use "vxresize" to grow vxfs directory in a stand-alone server without any problems, but I am just told to grow vxfs directorys in Veritas Cluster nodes.
Since I never done it before, would like to ask all the experts here to make sure the concept and steps will be fine... (1 Reply)
Discussion started by: sunnychen98
1 Replies
9. Solaris
hi all
i have a DLT tape in that tape backup is there is in veritas volume format and i want to restore it in ufs file system how can i do it?
right now i don't have veritas file system setup. i have only ufs file sysytem
please help some production data is to be restore. (3 Replies)
Discussion started by: nikhil kasar
3 Replies
10. Solaris
Hi all
I have a DLT tape in that tape backup is there is in veritas volume format and i want to restore it in ufs file system how can i do it?
right now i don't have veritas file system setup. i have only ufs file sysytem
please help some production data is to be restore.
backup was taken... (0 Replies)
Discussion started by: nikhil kasar
0 Replies
MOUNTD(8) BSD System Manager's Manual MOUNTD(8)
NAME
mountd -- service remote NFS mount requests
SYNOPSIS
Obsolete. See nfsd(8).
DESCRIPTION
The mountd daemon was formerly the server for NFS mount requests from NFS clients. This functionality has been moved into the NFS server
daemon nfsd(8).
Please refer to nfsd(8) for NFS server documenation.
The following is a list of former mountd options that are now available as nfsd(8) options:
mountd option nfsd option Description
-n -N allow non-root mounts
-r -R allow regular file mounts
exportsfile -F exportsfile alternate exports file
However, such configuration options are normally specified via nfs.conf(5).
When the NFS server is started, it loads the export host addresses and options into the kernel using the nfssvc(2) system call. After chang-
ing the list of exports (either directly or indirectly via a change in netgroup membership), the administrator should send a hangup signal to
the nfsd daemon to get it to reload the export information:
kill -s HUP `cat /var/run/nfsd.pid`
For backwards compatibility, the following should also work:
kill -s HUP `cat /var/run/mountd.pid`
Any errors encountered while processing the export entries will be logged via syslog(3).
FILES
/etc/exports the list of exported filesystems
/var/run/mountd.pid the pid of the currently running mountd
/var/run/mountdtab the current list of outstanding mounts served
/var/run/mountdexptab
information about exported file systems and directories (UUIDs, handles, ...)
SEE ALSO
nfsd(8), exports(5), nfs.conf(5), nfsstat(1), portmap(8), showmount(8)
HISTORY
The mountd utility first appeared in 4.4BSD. It's functionality was merged into nfsd(8) in Darwin 9.
BSD
November 10, 2006 BSD