03-25-2011
/dev/sdb is the entire disk, you can't mount an entire disk unless the entire disk is just one partition.
What kind of RAID is it? Is it a software raid? You may not be able to mount it until you activate it with mdadm, in which case it'll become a new device, /dev/md*.
Maybe it's activated itself already. That would explain why it thinks it's busy -- it's been "eaten" by the software RAID driver. Try ls -l /dev/md* to see if you have any software RAID devices available. And df -h for good measure to see what devices you already have mounted where.
This User Gave Thanks to Corona688 For This Post:
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi...
question is this:
How do I mount an LVD hotswap scsi drive in bay #2 on a netra using the mount command? volmgt doesn't seem to mount it and/or I don't know how to view the drives data if it's formatted which it may not be. This drive is not new out of the box so I'm not sure.
... (4 Replies)
Discussion started by: soulshaker
4 Replies
2. Solaris
Hi,
I set up a RAID 5 configuration and for some reason the volumes won't mount when the system boots. I have to manually mount them from the command line and all is fine.
Here's the vfstab entries:
#device device mount FS fsck mount mount
#to mount ... (2 Replies)
Discussion started by: rpollard001
2 Replies
3. UNIX for Advanced & Expert Users
I am having trouble mounting with cifs, but mounting the exact same command with smbfs works fine. The share is on another samba server and is set to full public guest access. # mount -t cifs //servername/sharename /mnt/temp -o password=""
mount error 13 = Permission denied Refer to the... (3 Replies)
Discussion started by: humbletech99
3 Replies
4. UNIX for Dummies Questions & Answers
Hi
Can someone tell me what are the differences between software and hardware raid ?
thx for help. (2 Replies)
Discussion started by: presul
2 Replies
5. Solaris
Dear ALl,
I have a RAID 5 volume which is as below
d120 r 60GB c1t2d0s5 c1t3d0s5 c1t4d0s5 c1t5d0s5
d7 r 99GB c1t2d0s0 c1t3d0s0 c1t4d0s0 c1t5d0s0
d110 r 99GB c1t2d0s4 c1t3d0s4 c1t4d0s4 c1t5d0s4
d8 r 99GB c1t2d0s1 c1t3d0s1... (2 Replies)
Discussion started by: jegaraman
2 Replies
6. Solaris
Hello All,
I have read enough of texts on Raid 01 and Raid 10 on solaris :wall: . But no-where found a way to create them using SVM. Some one pls tell me how to do or Post some link if that helps.
TIA
Curious
solarister (1 Reply)
Discussion started by: Solarister
1 Replies
7. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
8. Solaris
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Discussion started by: KhawHL
4 Replies
9. Red Hat
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
LEARN ABOUT FREEBSD
msdosfs
MSDOSFS(5) BSD File Formats Manual MSDOSFS(5)
NAME
msdosfs -- MS-DOS file system
SYNOPSIS
options MSDOSFS
DESCRIPTION
The msdosfs driver will permit the FreeBSD kernel to read and write MS-DOS based file systems.
The most common usage follows:
mount -t msdosfs /dev/ada0sN /mnt
where N is the partition number and /mnt is a mount point. Some users tend to create a /dos directory for msdosfs mount points. This helps
to keep better track of the file system, and make it more easily accessible.
It is possible to define an entry in /etc/fstab that looks similar to:
/dev/ada0sN /dos msdosfs rw 0 0
This will mount an MS-DOS based partition at the /dos mount point during system boot. Using /mnt as a permanent mount point is not advised
as its intention has always been to be a temporary mount point for floppy and ZIP disks. See hier(7) for more information on FreeBSD direc-
tory layout.
SEE ALSO
mount(2), unmount(2), mount(8), mount_msdosfs(8), umount(8)
AUTHORS
This manual page was written by Tom Rhodes <trhodes@FreeBSD.org>.
BSD
October 1, 2013 BSD