Sponsored Content
Operating Systems Solaris Solaris 10 on Dell R710 server Post 302506314 by tayyabq8 on Sunday 20th of March 2011 01:05:56 AM
Old 03-20-2011
Solaris 10 on Dell R710 server

Hello everyone,

We have an application which runs on SPARC machine, it is tested and runs without any problem, we are due to upgrade that machine but as cost-cutting measures we are thinking of buying a Dell PowerEdge 710 x86 machine this time, two questions..
1) any performance difference you reckon between a modern SPARC machine (e.g. SPARC M5000) and Dell R710 machine?
2) technically is there any thing which can stop our application running on x86 platform which successfully runs on SPARC platform?

Thanks in advance for any reply.

Cheers.
 

5 More Discussions You Might Find Interesting

1. Solaris

Installing Solaris 10 on Dell PowerEdge 2800

hi, i am trying to install solaris 10 (on 4 cd's downloaded from the sun website) on my dell poweredge 2800 server. 2 xeon processors, 2GB of RAM and 2 NICS, 73 GB SCSI (maxtor ultra320, 3.5 series), i can give more details on request... the installation crashes when trying to detect the NICS... (0 Replies)
Discussion started by: xinugeek
0 Replies

2. Filesystems, Disks and Memory

Linux and Dell 1500sc Poweredge Server

Does anybody no how to get around the fact that the Red Hat installation does not see the SCSI hard drives. It lets you manually pick the proper device, but still fails saying no drive detected (or something to that effect). I was going to install windows 2003 Server and use VMware...but again,... (1 Reply)
Discussion started by: Fatflea
1 Replies

3. UNIX for Dummies Questions & Answers

Dell monitor blinking with the Solaris

Hi I have experienced some problems with the new monitor on my Solaris WS (Solaris5.4). Old monitor (Sony ES200) died an we installed a new one (Dell Ultrascan P780) The system booted but the monitor statrted blinking at the rate about once in 5-7 seconds. This is espetially strange that the... (0 Replies)
Discussion started by: Andrey Malishev
0 Replies

4. Solaris

Solaris 10 and DELL TL-2000 Tape Library with ISCSI

Hello, i am trying to get following configuration up running, but get no access to the library roboter. Server: SunOS 5.10 Generic_138889-03 i86pc i386 i86pc DELL TL-2000: 1 Tape: IBM ULT3580-HH4 and Robot: 3573-TL, connected via ISCSI Bridge (build into the TL) ... (1 Reply)
Discussion started by: austin73
1 Replies

5. Solaris

Solaris 10 installation on dell power edge 1950

Hi, I am about to try Solaris 10 on a dell power edge 1950 server. I have googled and found some articles(2007) saying its not supported. Anybody tried this recently? Thanks in advance (2 Replies)
Discussion started by: ./hari.sh
2 Replies
nca.if(4)							   File Formats 							 nca.if(4)

NAME
nca.if - the NCA configuration file that specifies physical interfaces SYNOPSIS
/etc/nca/nca.if DESCRIPTION
Specify the physical interfaces for which the Solaris Network Cache and Accelerator ("NCA") feature will be configured in the nca.if con- figuration file. List the physical interfaces in the file, one per line. To configure NCA to listen on all physical interfaces present on the system backed by a hostname.{interface_name}, then list only an asterik ("*") in nca.if. When the ncakmod(1) initialization script is invoked during system boot, it will attempt to configure each physical interface specified in the nca.if file by using ncaconfd(1M). Note that there must be an accompanying hostname.{interface_name} file and an entry in /etc/hosts for the contents of hostname.{interface_name}. You must reboot in order to implement changes to the nca.if file. EXAMPLES
x86 Example 1: nca.if on x86 The following is an example of an nca.if file that would be used on an x86 system: iprb1 iprb6 iprb8 SPARC Example 2: nca.if on SPARC The following is an example of an nca.if file that would be used on a SPARC system: hme2 hme3 hme4 All Platforms Example 3: Configuring NCA to Listen on All Physical Interfaces The following example shows the contents of an nca.if file that would be used to configure either platform to listen on all physical inter- faces present on the system: * FILES
/etc/nca/nca.if Lists the physical interfaces on which NCA will run. /etc/hostname.{}{0-9} Lists all physical interfaces configured on the server. /etc/hosts Lists all host names associated with the server. Entries in this file must match with entries in /etc/host- name.{}{0-9} for NCA to function. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWncar | +-----------------------------+-----------------------------+ |Interface Stability |Evolving | +-----------------------------+-----------------------------+ SEE ALSO
nca(1), ncab2clf(1), ncakmod(1), ifconfig(1M), ncakmod.conf(4), ncalogd.conf(4), attributes(5) System Administration Guide: IP Services SunOS 5.10 18 Feb 2003 nca.if(4)
All times are GMT -4. The time now is 01:41 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy