Hi,
When I pinged a machin, I got to be seen a different kind of
reply from that machine.
This is as below : "Reply from 136.128.11.116: Source quench received." Which I felt like an un-usual message.
So what does this mean.
Regards & Thanks in advance.
Vishwa. (4 Replies)
Hi there hope list can help
I'm looking for a command that does the following
lets say i ping a server 00.00.000.00
and this server is up and running how do i get the ping command to return a UP or a Down
meaning
if the command is true do this
if the command is False do this
... (2 Replies)
We can ping out but the return never comes back even to localhost
ping localhost
PING loopback: (127.0.0.1): 56 data bytes
64 bytes from 127.0.0.1: icmp_seq=0 ttl=255 time=0 ms
it just sits there....
any ideas, any files to check (1 Reply)
Hi ,
I have one system installed on Linux Red Hat 3.0. I have ip of system 3.156.168.*** and i want to ping some port that is on this IP which command i can do this?
sam70 (1 Reply)
Hi All,
Need your help one more time.
I am trying to ping a linux machine which is not responding to ping.
However traceroute can reach the machine and I can log in to it by ssh. I have checked /proc/sys/net/ipv4/icmp_echo_ignore_all it is already set as "0".
It is not happening in the... (1 Reply)
I have an old MP-Ras Unix system. I have setup netowkring but am unable to ping any local network pcs or the default gateway. If i use the arp -a command I receive the correct mac address for all connected pcs but I cannot ping anything except the local address. Any help would be appreciative.
... (7 Replies)
Hi,
I develop simple animation ping script on Solaris Platform. It is like Cisco ping.
Examples and source code are below.
bash-3.00$ gokcell 152.155.180.8 30
Sending 30 Ping Packets to 152.155.180.8
!!!!!!!!!!!!!.!!!!!!!!!!!!!!!.
% 93.33 success... % 6.66 packet loss...... (1 Reply)
I am unable to ping my remote server.My server is unable to ping the same. both are able to ping the gateway. both the ip's are on same network.i use a proxy tunnel on my remote server.Help if any clues. (6 Replies)
Hi
I am using perl to ping a list of nodes - with script below :
$p = Net::Ping->new("icmp");
if ($p->ping($host,1)){
print "$host is alive.\n";
}
else {
print "$host is unreacheable.\n";
}
$p->close();... (4 Replies)
help with bash script!
im am working on this script to make sure my server will stay online, so i made this script..
HOSTS="192.168.138.155"
COUNT=4
pingtest(){
for myhost in "$@"
do
ping -c "$COUNT" "$myhost" &&return 1
done
return 0
}
if pingtest $HOSTS
#100% failed... (4 Replies)
Discussion started by: mort3924
4 Replies
LEARN ABOUT DEBIAN
macping
MACPING(1) General Commands Manual MACPING(1)NAME
macping - A tool for pinging other RouterOS or mactelnetd devices
SYNOPSIS
mactelnet [options] <MAC-Address|hostname>
DESCRIPTION
This tool enables you to ping other RouterOS or MAC-Telnetd enabled devices. You can ping either a hostname or a MAC address. If speci-
fied, the hostname (identity) will be looked up via MNDP discovery.
OPTIONS
These programs follow the usual GNU command line syntax. A summary of options is included below.
-f Fast mode, do not wait before sending next ping request. The next ping will be sent immediately when the last ping is received. This
cannot be used with -c 0
-s Specify the amount of bytes to send in each ping packet, up to ~1400 bytes.
-c Number of packets to send before exiting. A value of 0 means unlimited packets and the tool must be exited with Control + C.
-h Show summary of options.
-v Show version of program.
SEE ALSO mndp(1), mactelnet(1), mactelnetd(1).
AUTHOR
macping was written by Hakon Nessjoen <haakon.nessjoen@gmail.com>.
This manual page was written by Hakon Nessjoen <haakon.nessjoen@gmail.com>, for the Debian project (and may be used by others).
February 27, 2011 MACPING(1)