03-04-2011
The bge interface is a gigabit interface based on the the Broadcom 5704 chipset.
The e1000g is an Intel PRO/1000 gigabit interface based on 825XX chip.
The eri interface is a 10/100Mbit interface based on the RIO GEM chip.
This User Gave Thanks to fpmurphy For This Post:
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. IP Networking
The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out >
link ok < when i connected >
But... (0 Replies)
Discussion started by: DPAI
0 Replies
3. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
4. UNIX for Dummies Questions & Answers
Hi!.
I have problems installing my network card under
ther redhat kernel.
First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.
also i huse my network card to connect to the net
trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies
5. UNIX for Dummies Questions & Answers
which unix cmd will give the following result...
Node Name Task Name ID Status Network
NUTTS CTP_E 1000 In Service X25/OFF TCP/ON
MUSKET CTP_E 2011 Unreachable X25/OFF TCP/OFF
... (0 Replies)
Discussion started by: rahulrathod
0 Replies
6. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
7. Solaris
Hi Experts,
Can we use some command from unix to find the available network interface? I did tried
Its listing following, however how can I decide the which vender card is attached
e.g. if its hme , bge or some thing else
Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies
8. Solaris
Hi,
/sbin/ifconfig -a
when i login as guest user , output like below,
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
eri0: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 1500 index 2
inet... (5 Replies)
Discussion started by: forumguest
5 Replies
9. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
10. UNIX for Beginners Questions & Answers
Hi ALL,
I am trying to collect and print all the network interface details in linux shell script.
operating system : centos 7
Below is my shell script :
#!/usr/bin/env bash
for i in $(ip link show | awk -F: '$1>0 {print $2}')
do
if ; then
echo -e... (2 Replies)
Discussion started by: balu1234
2 Replies
MY(4) BSD Kernel Interfaces Manual MY(4)
NAME
my -- Myson Technology Ethernet PCI driver
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device my
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_my_load="YES"
DESCRIPTION
The my driver provides support for various NICs based on the Myson chipset. The Myson chipset is a variant of the DEC Tulip NIC chipset.
The driver will work with almost any MII-compliant PHY, thus failure to positively identify the chip is not a fatal error.
HARDWARE
The my driver provides support for various NICs based on the Myson chipset. Supported models include:
o Myson MTD800 PCI Fast Ethernet chip
o Myson MTD803 PCI Fast Ethernet chip
o Myson MTD89X PCI Gigabit Ethernet chip
SEE ALSO
altq(4), de(4), netintro(4), pci(4), ifconfig(8)
HISTORY
The my driver first appeared in FreeBSD 4.6.
AUTHORS
The my driver was written by Myson Technology Inc.
This manual page was written by Hiten M. Pandya <hmp@FreeBSD.org>.
BUGS
The my driver does not support Power Management Events (PME).
BSD March 11, 2007 BSD