Solaris not recognizing RAID 5 disks Post: 302501700

10 More Discussions You Might Find Interesting

1. Solaris

RAID in Solaris 9

All, Is there a way to RAID the disks in Solaris 9? Solaris 8 provided DiskSuite for mirroring disk drives. Is there a GUI for DiskSuite in Solaris 9? Thanks, Mike

2. Solaris

disks in solaris

whats the command to find name of all disks. Is it iostat -En ?

3. Red Hat

We have a Red Hat linux server running on IBM x445 hardware. There are external disks in an IBM EXP300 disk enclosure. The system is running RAID 5. One of the four IBM disks (73.4 GB 10k FRU 06P5760) has become faulty. The system is still up and running OK because of the RAID. In that same EXP300...

4. Solaris

Move disks to different StorEdge, keeping RAID

Hi. I need to move a 5 disk RAID5 array from a SE3310 box to a different SE3310 array. After installing the disks in the "new" StorEdge device, I "would like" ;) to be able have access to the data which is on the RAID. Essentially, the quesion is, how can this be done? :confused: I checked...

5. Linux

If i don't have raid disks can i shut down dmraid device-mapper?

hello my centOS newly installed system loading dmraid modules on startup I did remove all LVM/raid things from system installation menus and after installation too but dmraid is still there and he says: no raid disks found also I did modprobe -r dm_raid45 and it do remove it but only until...

6. Solaris

Solaris 9 not recognizing CDROM drive

Hello, I've read many posts that offer tips on how to mount a CDROM but I haven't seen any on how to get the system to recognize the CDROM drive. I was transferring files from CDROM to the hard drive successfully. I entered the third CDROM and the system refused to automount it. I tried...

7. AIX

SCSI PCI - X RAID Controller card RAID 5 AIX Disks disappeared

Hello, I have a scsi pci x raid controller card on which I had created a disk array of 3 disks when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk ) suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI...

8. Solaris

Solaris 10 Installation - Disks missing, and Raid

Hey everyone. First, let me start by saying I'm primarily focused on linux boxes, and just happened to get pulled into building two T5220's. I'm not super educated on sun boxes. Both T5220's have 8 146GB 15k SAS drives. Inside the service processor, I can run SHOW /SYS/HDD{0-7} and they all come...

9. Solaris

Hardware RAID using three disks

Dear All , Pl find the below command , # raidctl -l Controller: 1 Volume:c1t0d0 Disk: 0.0.0 Disk: 0.1.0 Disk: 0.3.0 # raidctl -l c1t0d0 Volume Size Stripe Status Cache RAID Sub Size ...

10. Solaris

Root user not recognizing on Solaris-10 (shadow file corruption)

Hello, I got into a wired state on one of solaris 10 server. When I noticed that server is having some issue, I found that there were dumpadm.conf entries in /etc/shadow and real entries were wiped of. Probably somebody fat fingers. I was able to boot into failsafe, break SVM mirror, copied...

LEARN ABOUT REDHAT

tapeinfo

TAPEINFO(1)						      General Commands Manual						       TAPEINFO(1)

NAME

       tapeinfo - report SCSI tape device info

SYNOPSIS

       tapeinfo -f <scsi-generic-device>

DESCRIPTION

       The  tapeinfo  command  reads  various information from SCSI tape drives that is not generally available via most vendors' tape drivers. It
       issues raw commands directly to the tape drive, using either the  operating  system's  SCSI  generic  device  (	e.g.  /dev/sg0	on  Linux,
       /dev/pass0 on FreeBSD) or the raw SCSI I/O ioctl on a tape device on some operating systems.

       One  good  time	to  use 'tapeinfo' is immediately after a tape i/o operation has failed. On tape drives that support HP's 'tapealert' API,
       'tapeinfo' will report a more exact description of what went wrong.

       Do be aware that 'tapeinfo' is not a substitute for your operating system's own 'mt' or similar tape driver control program. It is intended
       to supplement, not replace, programs like 'mt' that access your operating system's tape driver in order to report or set information.

OPTIONS

       The first argument, given following -f , is the SCSI generic device corresponding to your tape drive.  Consult your operating system's doc-
       umentation for more information (for example, under Linux these are generally start at /dev/sg0 under FreeBSD these start at /dev/pass0).

       Under FreeBSD, 'camcontrol devlist' will tell you what SCSI devices you have, along with which 'pass' device controls  them.  Under  Linux,
       "cat /proc/scsi/scsi" will tell you what SCSI devices you have.

BUGS AND LIMITATIONS

       This program has only been tested on Linux with a limited number of tape drives (HP DDS4, Seagate AIT).

AVAILABILITY

       tapeinfo  is  currently being maintained by Eric Lee Green <eric@badtux.org> formerly of Enhanced Software Technologies Inc. The 'mtx' home
       page is http://mtx.sourceforge.net and the actual code is currently available there and via CVS from http://sourceforge.net/projects/mtx/ .

SEE ALSO

       mt(1),mtx(1),scsitape(1)

								    TAPEINFO1.0 						       TAPEINFO(1)

10 More Discussions You Might Find Interesting

1. Solaris

RAID in Solaris 9

Discussion started by: bubba112557

2. Solaris

disks in solaris

Discussion started by: vikashtulsiyan

3. Red Hat

IBM RAID disks

Discussion started by: pdudley

4. Solaris

Move disks to different StorEdge, keeping RAID

Discussion started by: alexs77