03-04-2011
when you say you cant see the raid 5 drives, how are you checking?
what says # format < /dev/null
have you tried a reconfiguration boot?
10 More Discussions You Might Find Interesting
1. Solaris
All,
Is there a way to RAID the disks in Solaris 9? Solaris 8 provided DiskSuite for mirroring disk drives. Is there a GUI for DiskSuite in Solaris 9?
Thanks,
Mike (2 Replies)
Discussion started by: bubba112557
2 Replies
2. Solaris
whats the command to find name of all disks. Is it iostat -En ? (1 Reply)
Discussion started by: vikashtulsiyan
1 Replies
3. Red Hat
We have a Red Hat linux server running on IBM x445 hardware. There are external disks in an IBM EXP300 disk enclosure. The system is running RAID 5. One of the four IBM disks (73.4 GB 10k FRU 06P5760) has become faulty. The system is still up and running OK because of the RAID. In that same EXP300... (3 Replies)
Discussion started by: pdudley
3 Replies
4. Solaris
Hi.
I need to move a 5 disk RAID5 array from a SE3310 box to a different SE3310 array. After installing the disks in the "new" StorEdge device, I "would like" ;) to be able have access to the data which is on the RAID.
Essentially, the quesion is, how can this be done? :confused:
I checked... (5 Replies)
Discussion started by: alexs77
5 Replies
5. Linux
hello
my centOS newly installed system loading dmraid modules on startup
I did remove all LVM/raid things from system installation menus and after installation too but dmraid is still there
and he says: no raid disks found
also I did modprobe -r dm_raid45 and it do remove it but only until... (7 Replies)
Discussion started by: tip78
7 Replies
6. Solaris
Hello,
I've read many posts that offer tips on how to mount a CDROM but I haven't seen any on how to get the system to recognize the CDROM drive.
I was transferring files from CDROM to the hard drive successfully. I entered the third CDROM and the system refused to automount it. I tried... (2 Replies)
Discussion started by: TrueSon
2 Replies
7. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
8. Solaris
Hey everyone. First, let me start by saying I'm primarily focused on linux boxes, and just happened to get pulled into building two T5220's. I'm not super educated on sun boxes.
Both T5220's have 8 146GB 15k SAS drives. Inside the service processor, I can run SHOW /SYS/HDD{0-7} and they all come... (2 Replies)
Discussion started by: msarro
2 Replies
9. Solaris
Dear All ,
Pl find the below command ,
# raidctl -l
Controller: 1
Volume:c1t0d0
Disk: 0.0.0
Disk: 0.1.0
Disk: 0.3.0
#
raidctl -l c1t0d0
Volume Size Stripe Status Cache RAID
Sub Size ... (10 Replies)
Discussion started by: jegaraman
10 Replies
10. Solaris
Hello,
I got into a wired state on one of solaris 10 server. When I noticed that server is having some issue, I found that there were dumpadm.conf entries in /etc/shadow and real entries were wiped of. Probably somebody fat fingers.
I was able to boot into failsafe, break SVM mirror, copied... (25 Replies)
Discussion started by: solaris_1977
25 Replies
LEARN ABOUT REDHAT
volcheck
volcheck(1) User Commands volcheck(1)
NAME
volcheck - checks for media in a drive and by default checks all floppy media
SYNOPSIS
volcheck [-v] [-i secs] [-t secs] pathname
DESCRIPTION
The volcheck utility tells Volume Management to look at each dev/pathname in sequence and determine if new media has been inserted in the
drive.
The default action is to volcheck all checkable media managed by volume management.
OPTIONS
The following options are supported:
-i secs Set the frequency of device checking to secs seconds. The default is 2 seconds. The minimum frequency is 1 second.
-t secs Check the named device(s) for the next secs seconds. The maximum number of seconds allowed is 28800, which is 8 hours. The fre-
quency of checking is specified by -i. There is no default total time.
-v Verbose.
OPERANDS
The following operands are supported:
pathname The path name of a media device.
EXAMPLES
Example 1: A sample of the volcheck command.
The following example
example% volcheck -v /dev/diskette
/dev/diskette has media
asks Volume Management to examine the floppy drive for new media.
The following example
example% volcheck -i 2 -t 600 /dev/diskette1 &
asks Volume Management if there is a floppy in the floppy drive every 2 seconds for 600 seconds (10 minutes).
FILES
/dev/volctl Volume Management control port
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWvolu |
+-----------------------------+-----------------------------+
SEE ALSO
eject(1), volcancel(1), volmissing(1) rmmount(1M), vold(1M), rmmount.conf(4), vold.conf(4), attributes(5), volfs(7FS)
WARNINGS
Due to a hardware limitation in many floppy drives, the act of checking for media causes mechanical action in the floppy drive. Continu-
ous polling of the floppy drive will cause the drive to wear out. It is recommended that polling the drive only be performed during periods
of high use.
SunOS 5.10 21 Feb 1997 volcheck(1)