Sponsored Content
Operating Systems Linux Red Hat RHEL 5.6 Slow rsync to NFS array Post 302501438 by mark54g on Thursday 3rd of March 2011 01:59:54 PM
Old 03-03-2011
Do you have a duplex mismatch? That sounds like a configuration issue.
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

ls -l over NFS slow

I have an HP-UX server with a Network Appliance Filer attached over Gigabit Ethernet. I am noticing very slow response time when using "ls -l" on one directory on one of the several NFS mounted filesystems. The "ls" command by itself does not seem to be a problem. Typically I get a response within... (3 Replies)
Discussion started by: keelba
3 Replies

2. UNIX for Dummies Questions & Answers

Remote server mount slow - NFS

Hi, Following my last post I've mounted the remote server on my local server. However copying files from this mounted server is increadbily slow. If I copy files using rcp it's very fast so I assume there must be a setting somewhere? Any help appreicated. Thanks (2 Replies)
Discussion started by: AngryBunny
2 Replies

3. Red Hat

NFS writing so slow

Hi, I facing an NFS problem. I have machine1, which has diskA and diskB, and machine2, both are Mandriva 2009 Linux. When I am on machine2 and NFS mount both diskA and diskB of machine1. Writing to diskA is very fast, but writing to diskB is very slow. I tried different mount rsize and wsize... (2 Replies)
Discussion started by: hiepng
2 Replies

4. Red Hat

file writing over nfs very slow

Hi guys, I am trying something. I wrote a simple shell program to test something where continuous while loop writes on a file over the nfs. The time taken to write "hello" 3000 times take about 10 sec which is not right. Ideally it should take fraction of seconds. If I write on the local disk, it... (1 Reply)
Discussion started by: abhig
1 Replies

5. Red Hat

cannot ssh (use NFS) on RHEL box, but can mount external & ssh out of RHEL box

Ok, Im trying to get NFS working on my RHEL 5 box, apparently i can use the box as a client, but not as a server. If it helps i cant ssh into the box (server), but as a client ssh works fine. Ive configured server: /etc/hosts.allow: all : all all :all@all setup my /etc/exports file... (4 Replies)
Discussion started by: drs.grid
4 Replies

6. AIX

Slow NFS when cio/dio enabled

Hi, I have a bit of a NFS problem on AiX 6.1 : When I set the mount to cio and dio - needed for a database app - Everything slows down. The following is copying 700mb, top one is a normal mount bottom one is a mount with the cio/dio option enabled : # ./a.sh Wed Jan 11 11:41:24 GMT 2012... (5 Replies)
Discussion started by: AJCG1976
5 Replies

7. UNIX for Dummies Questions & Answers

Rsync Can I delete .NFS and .fuse files

Hello, I have some files in a local directory and perform an rsync command with the files in a remote directory, Now when I checked the files in the local and the remote directory, I found some strange filetypes such as this: .nfs0000000001d0c8e000002ff2 , .fuse_hidden000014da00000001 etc etc,... (3 Replies)
Discussion started by: ajayram
3 Replies

8. Red Hat

RHEL 7.1 autofs permissions do not match NFS servers

RHEL 7.1 client using autofs to mount a NIS map of home directories being exported by a Solaris 10x86 nfs server. The owner and group are correct on the NFS server, but on the RHEL client, the owner and group end up being nobody nobody. The USERS and GROUPS are NIS maps as well. They are... (2 Replies)
Discussion started by: mrmurdock
2 Replies

9. Solaris

RHEL NFS share on Solaris 11.3 vers=4

NFS server: RHEL:6 /nfsdb 192.168.8.10/28(rw,sync,no_root_squash) 192.168.7.10/28(rw,sync,no_root_squash) Client: Solaris 11.3 vfstab entry : 192.168.8.9:/nfsdbarch - /archive_data nfs - yes rw,soft,vers=4 # ls -ld /archive_data drwxr-xr-x 4 root root... (3 Replies)
Discussion started by: Shirishlnx
3 Replies

10. Solaris

Rsync quite slow (using very little cpu): how to improve its speed?

I have "inherited" a OmniOS (illumos based) server. I noticed rsync is significantly slower in respect to my reference, FreeBSD 12-CURRENT, running on exactly same hardware. Using same hardware, same command with same source and target disks, OmniOS r151026 gives: test@omniosce:~# time... (11 Replies)
Discussion started by: priyadarshan
11 Replies
sg_get_network_iface_stats(3)				     Library Functions Manual				     sg_get_network_iface_stats(3)

NAME
sg_get_network_iface_stats - get network interface statistics SYNOPSIS
#include <statgrab.h> sg_network_iface_stats *sg_get_network_iface_stats(int *entries); DESCRIPTION
The sg_get_network_iface_stats function takes a pointer to an int, entries, which is filled with the number of network interfaces the machine has. This is needed to know how many sg_network_iface_stats structures have been returned. A pointer is returned to the first sg_network_iface_stats. sg_get_network_iface_stats returns statistics about the network interfaces in the machine. Specifically, it returns the speed of the inter- face, the duplex state, and whether it is currently up. RETURN VALUES
The sg_get_network_iface_stats returns a pointer to a structure of type sg_network_iface_stats. typedef enum{ SG_IFACE_DUPLEX_FULL, SG_IFACE_DUPLEX_HALF, SG_IFACE_DUPLEX_UNKNOWN }sg_iface_duplex; Note: The SG_IFACE_DUPLEX_UNKNOWN value could mean that duplex hasn't been negotiated yet. typedef struct{ char *interface_name; int speed; sg_iface_duplex duplex; int up; }sg_network_iface_stats; interface_name The name known to the operating system. (eg. on linux it might be eth0) speed The speed of the interface, in megabits/sec. duplex The duplex state the interface is in. See sg_iface_duplex for permitted values. up Whether the interface is up. SEE ALSO
statgrab(3) WEBSITE
http://www.i-scream.org/libstatgrab/ i-scream $Date: 2005/07/13 09:31:53 $ sg_get_network_iface_stats(3)
All times are GMT -4. The time now is 11:02 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy