I've had a VXFS filesystem get corrupted and now it won't mount.
Can I run a fsck -y on the raw disk device or should something be
done within veritas? Veritas does not see the disk at the moment. (2 Replies)
Hi there,
My task is to replace the two 73 G disks with two 143 G disks , which has vxvm 4.1 running on it. I would like to know whether the steps iam following are correct.
1. Break the sub-disks, plexes of the root mirror.
2. Remove the sub-disks,plexes of the root mirror.
3. Remove one of... (10 Replies)
I have a bogus disk that keeps showing up as failed from vxdisk list
- - disk hpdg failed was:c2t0d11s2
There isnt any c2 devices on the system:
# ls /dev/dsk/c2*
/dev/dsk/c2*: No such file or directory
# ls /dev/rdsk/c2*
/dev/rdsk/c2*: No such file or... (3 Replies)
I installed new internal disks in my p570. They will be part of a new AIX vg. Unfortunately, we have Veritas Volume Manager running on this AIX 5.2 ml 10 box. Veritas has grabbed control of the disks. I want AIX LVM to control the disks.
I cannot get these disks free of Veritas:
<lspv... (2 Replies)
People i have an a storage i create two virtual disk 1 y 2.
In the virtual disk 1 i configure 8 volumes and in the Vd2 configure 5 volumes.
Now i want to create a disk group called Prod2 y Dev2 but when i go to vxdiskadm and i choose add disk o encapusalte when i press list to list the disk... (0 Replies)
Need help getting all disk devices back on node 2 the same as node 1.
Recently Veritas and/or Sun cluster got wrecked on my 2 node Sun cluster after installing the latest patch cluster. I backed out the patches and then node 2 could see only half of the devices and Veritas drives (though format... (0 Replies)
Hi,
a little while ago, one of the GPT Partitioned hard disk had gone faulty in a Mirror RAID and is now successfully replaced.
here is how I did that.
1) created identical partition table on the new disk.
2) attached the mirrors using md commands.
The whole procedure is given... (5 Replies)
Hi,
a little while ago, one of the GPT Partitioned hard disk had gone faulty in a Mirror RAID and is now successfully replaced.
here is how I did that.
1) created identical partition table on the new disk.
2) attached the mirrors using md commands.
The whole procedure is given below:... (2 Replies)
Hi Experts,
I wanted to extend a veritas file system which is running on veritas cluster and mounted on node2 system.
#hastatus -sum
-- System State Frozen
A node1 running 0
A node2 running 0
-- Group State
-- Group System Probed ... (1 Reply)
OSLevel: 5300-10-02-0943
System Model: IBM,8203-E4A
Power 6
==
Hi!
I replaced a failed pdisk in the raid enclosure as follows,
- rmdev -l 'pdisk18' '-d'
- Replaced it.
- cfgmgr (detected)
- I can see the new drive, with the correct serial #
lscfg -v -l pdisk18
pdisk18... (2 Replies)
Discussion started by: estrar
2 Replies
LEARN ABOUT REDHAT
setfdprm
SETFDPRM(8) Linux Programmer's Manual SETFDPRM(8)NAME
setfdprm - sets user-provided floppy disk parameters
SYNOPSIS
setfdprm [ -p ] device name
setfdprm [ -p ] device size sectors heads tracks stretch gap rate spec1 fmt_gap
setfdprm [ -c ] device
setfdprm [ -y ] device
setfdprm [ -n ] device
DESCRIPTION
setfdprm is a utility that can be used to load disk parameters into the auto-detecting floppy devices, to clear old parameter sets and to
disable or enable diagnostic messages.
Without any options, setfdprm loads the device (usually /dev/fd0 or /dev/fd1) with a new parameter set with the name entry found in
/etc/fdprm (usually named 360/360, etc.). These parameters stay in effect until the media is changed.
-p device name
Permanently loads a new parameter set for the specified auto-configuring floppy device for the configuration with name in
/etc/fdprm. Alternatively, the parameters can be given directly from the command line.
-c device
Clears the parameter set of the specified auto-configuring floppy device.
-y device
Enables format detection messages for the specified auto-configuring floppy device.
-n device
Disables format detection messages for the specified auto-configuring floppy device.
BUGS
This documentation is grossly incomplete.
FILES
/etc/fdprm
AUTHOR
Werner Almesberger (almesber@nessie.cs.id.ethz.ch)
Linux 0.99 20 November 1993 SETFDPRM(8)