02-27-2011
How can I monitor network in CentOS .5.5 , my application refuse to read sockets
Hi
I have wired problem with one of my applications (servers ) , its suddenly starts to read socket and before it written back , the connection is closed
this is what I see in my logs . is there any took in Linux centos that lets me see what is happening in this time frame ?
9 More Discussions You Might Find Interesting
1. Programming
I am developing a Network Appliation to monitor computers in a network.
Specs are
App monitors the current web page viewed in each system
App also can shutdown the computer in the network
App can show all process run by each computer in the network
I am now confused how to start my... (2 Replies)
Discussion started by: valaparambil88
2 Replies
2. Linux
Hi,
For some reason my network card started going 10Mb/s half duplex instead of 1000Mb/s full duplex. System is connected to 8x1Gb HP switch.
Other devices connect fine through the switch and get full 1Gb network.
I have Centos 5 with all updates. Driver comes from elrepo and as well is... (1 Reply)
Discussion started by: columb
1 Replies
3. Programming
I am trying to make a server and client, the client will choose between some options and the server will react accordingly.
After a some reads and writes that work the server needs to read from client an INT i use this:
read(newSd,&k,sizeof(int));But even if all the other times there was no... (1 Reply)
Discussion started by: theSling
1 Replies
4. AIX
I have configured a custom application monitor with restart count = 3.
say the application has restarted 2 times, if the application fail 2 more times within restart interval, it will failover.
Is there any counter to tell me the recent restart count?
Thanks!! (1 Reply)
Discussion started by: skeyeung
1 Replies
5. Red Hat
I was testing Networking Teaming (activebackup) with a VM hosted on VmWare Workstation and VirtualBox, and the result is, if the active interface is down, the system is not using the backup interface.
Tested on both CentOS / RHEL 7
Please find below the command I have used to configure teaming.... (0 Replies)
Discussion started by: atanubanerji
0 Replies
6. Web Development
Hi All,
Frankly I'm new to Linux Environment. While we are trying to Host an ASP.NET 5 Web Application on Centos OS7 Web hosting Server. There were couple of steps which we are supposed to go through, please see this link -
We are stuck at Create a Container & then Running the Container,... (1 Reply)
Discussion started by: John Fredric
1 Replies
7. Emergency UNIX and Linux Support
Hi all,
I need to add domain and search parameters to resolv.conf, however network manager overwrites.
Setting the PEERDNS=No in the interface file seems to have no effect on this behaviour.
Sadly I cannot just disable NM as these are not my hosts, I'm just attempting to install a platform... (3 Replies)
Discussion started by: Skrynesaver
3 Replies
8. IP Networking
My son does homework on a school laptop. I was thinking about setting up a gateway on my home network, so that I can monitor web traffic and know if he is doing his homework without standing over his shoulder. Ideally I would like to use the Raspberry Pi Model b that I already have. However, I... (15 Replies)
Discussion started by: gandolf989
15 Replies
9. Infrastructure Monitoring
After setting up MQTT and testing some ESP8266 and ESP32 modules, where I noted that testing in Programming ESP32 (ESP-WROOM-32) as an MQTT Client Subscribed to Linux Server Load Average Messages, I was so impressed with MQTT that I installed MQTT on three different computers, instantly and... (2 Replies)
Discussion started by: Neo
2 Replies
udp(7) Miscellaneous Information Manual udp(7)
NAME
udp - Internet user datagram protocol (UDP)
SYNOPSIS
#include <sys/socket.h> #include <netinet/in.h>
The following is the socket call for AF_INET sockets:
s = socket(AF_INET, SOCK_DGRAM, 0); The following is the socket call for AF_INET6 sockets:
s = socket(AF_INET6, SOCK_DGRAM, 0);
DESCRIPTION
UDP is a simple, unreliable datagram protocol that is used to support the SOCK_DGRAM abstraction for the Internet Protocol family. UDP
sockets are connectionless, and are normally used with the sendto() and recvfrom() functions, though the connect() function may also be
used to fix the destination for future packets, in which case the recv() or read() and send() or write() functions may be used.
UDP address formats are identical to those used by TCP. In particular, UDP provides a port identifier in addition to the normal Internet
address format. Note that the UDP port space is separate from the TCP port space (that is, a UDP port may not be "connected" to a TCP
port). In addition, IPv4 broadcast packets may be sent (assuming the underlying network supports this) by using a reserved "broadcast
address"; this address is network interface dependent. There is no broadcast address in IPv6.
Options at the IP transport level may be used with UDP; see the ip() reference page.
ERRORS
If a socket operation fails, errno may be set to one of the following values: An attempt was made to create a socket with a port that has
already been allocated. An attempt was made to create a socket with a network address for which no network interface exists. The socket
is already connected. This error occurs when trying to establish connection on a socket or when trying to send a datagram with the desti-
nation address specified. The system ran out of memory for an internal data structure. The destination address of a datagram was not
specified, and the socket has not been connected.
RELATED INFORMATION
Functions: getsockopt(2), recv(2), send(2), socket(2)
Files: netintro(7), inet(7), ip(7) delim off
udp(7)