How can I monitor network in CentOS .5.5 , my application refuse to read sockets Post: 302500095

9 More Discussions You Might Find Interesting

1. Programming

Help in developing a Network Appliation to monitor pc in a network

I am developing a Network Appliation to monitor computers in a network. Specs are App monitors the current web page viewed in each system App also can shutdown the computer in the network App can show all process run by each computer in the network I am now confused how to start my...

2. Linux

Network 10Mb/s half duplex only. r8168 on Centos 5.

Hi, For some reason my network card started going 10Mb/s half duplex instead of 1000Mb/s full duplex. System is connected to 8x1Gb HP switch. Other devices connect fine through the switch and get full 1Gb network. I have Centos 5 with all updates. Driver comes from elrepo and as well is...

3. Programming

help: problem with sockets write/read

I am trying to make a server and client, the client will choose between some options and the server will react accordingly. After a some reads and writes that work the server needs to read from client an INT i use this: read(newSd,&k,sizeof(int));But even if all the other times there was no...

4. AIX

powerha application monitor restart counter?

I have configured a custom application monitor with restart count = 3. say the application has restarted 2 times, if the application fail 2 more times within restart interval, it will failover. Is there any counter to tell me the recent restart count? Thanks!!

5. Red Hat

Network Teaming not working in RHEL/CentOS 7

I was testing Networking Teaming (activebackup) with a VM hosted on VmWare Workstation and VirtualBox, and the result is, if the active interface is down, the system is not using the backup interface. Tested on both CentOS / RHEL 7 Please find below the command I have used to configure teaming....

6. Web Development

ASP.NET 5 Application on Centos OS7 Web Hosting Server

Hi All, Frankly I'm new to Linux Environment. While we are trying to Host an ASP.NET 5 Web Application on Centos OS7 Web hosting Server. There were couple of steps which we are supposed to go through, please see this link - We are stuck at Create a Container & then Running the Container,...

7. Emergency UNIX and Linux Support

Centos 7 Network Manager overwriting resolv.conf

Hi all, I need to add domain and search parameters to resolv.conf, however network manager overwrites. Setting the PEERDNS=No in the interface file seems to have no effect on this behaviour. Sadly I cannot just disable NM as these are not my hosts, I'm just attempting to install a platform...

8. IP Networking

I would like to monitor network traffic for a computer on my network

My son does homework on a school laptop. I was thinking about setting up a gateway on my home network, so that I can monitor web traffic and know if he is doing his homework without standing over his shoulder. Ideally I would like to use the Raspberry Pi Model b that I already have. However, I...

9. Infrastructure Monitoring

Using Node-RED and MQTT to Monitor Server and Application Stats

After setting up MQTT and testing some ESP8266 and ESP32 modules, where I noted that testing in Programming ESP32 (ESP-WROOM-32) as an MQTT Client Subscribed to Linux Server Load Average Messages, I was so impressed with MQTT that I installed MQTT on three different computers, instantly and...

LEARN ABOUT SUSE

dbus-monitor

dbus-monitor(1) 					      General Commands Manual						   dbus-monitor(1)

NAME

       dbus-monitor - debug probe to print message bus messages

SYNOPSIS

       dbus-monitor [--system | --session | --address ADDRESS] [--profile | --monitor] [watch expressions]

DESCRIPTION

       The  dbus-monitor command is used to monitor messages going through a D-Bus message bus.  See http://www.freedesktop.org/software/dbus/ for
       more information about the big picture.

       There are two well-known message buses: the systemwide message bus (installed on many systems as the "messagebus"  service)  and  the  per-
       user-login-session  message  bus (started each time a user logs in).  The --system and --session options direct dbus-monitor to monitor the
       system or session buses respectively.  If neither is specified, dbus-monitor monitors the session bus.

       dbus-monitor has two different output modes, the 'classic'-style monitoring mode and profiling mode. The profiling format is a compact for-
       mat  with a single line per message and microsecond-resolution timing information. The --profile and --monitor options select the profiling
       and monitoring output format respectively. If neither is specified, dbus-monitor uses the monitoring output format.

       In order to get dbus-monitor to see the messages you are interested in, you should specify a set of watch expressions as you  would  expect
       to be passed to the dbus_bus_add_match function.

       The message bus configuration may keep dbus-monitor from seeing all messages, especially if you run the monitor as a non-root user.

OPTIONS

       --system
	      Monitor the system message bus.

       --session
	      Monitor the session message bus.	(This is the default.)

       --address ADDRESS
	      Monitor an arbitrary message bus given at ADDRESS.

       --profile
	      Use the profiling output format.

       --monitor
	      Use the monitoring output format.  (This is the default.)

EXAMPLE

       Here is an example of using dbus-monitor to watch for the gnome typing monitor to say things

	 dbus-monitor "type='signal',sender='org.gnome.TypingMonitor',interface='org.gnome.TypingMonitor'"

AUTHOR

       dbus-monitor was written by Philip Blundell.  The profiling output mode was added by Olli Salli.

BUGS

       Please send bug reports to the D-Bus mailing list or bug tracker, see http://www.freedesktop.org/software/dbus/

																   dbus-monitor(1)