02-25-2011
You are most welcome, but was it helpful?
take care
10 More Discussions You Might Find Interesting
1. Solaris
Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
Discussion started by: xiaochensg
5 Replies
2. AIX
Hi All,
SUN emulex HBA card has been installed on P520 box.
When i run the cfgmgr i am getting the following message.
lpar2#cfgmgr
cfgmgr: 0514-621 WARNING: The following device packages are required for
device support but are not currently installed.... (0 Replies)
Discussion started by: b_manu78
0 Replies
3. IP Networking
I have one 4GB, dual port HBA. Is each port rated for 4GB, or is it the whole HBA rated for 4GB?
Also, how do I determine which is port0 / port1 with "lscfg -vl fcs0" command. Thanks. (0 Replies)
Discussion started by: jwholey
0 Replies
4. Solaris
I understand that fcinfo hba-port should show information(WWN, HBA vendor, etc..) but my result show "No adapter found". If I used grep -i 'version' /var/adm/messages* then I see my installed HBA (QLogic FCode at 2.00.09).. I am wondering why and what I had failed to install?
Thanks in advance.... (23 Replies)
Discussion started by: Y4Net
23 Replies
5. Solaris
Hi Gurus
I need to know few things related to HBA port & fcinfo command
I have a server where there are 4 HBA ports cards are their. Out of 4 ports 2 are in use & 2 are not in use when I check it physicall. Now I want to know the command through which I can get information about all above... (6 Replies)
Discussion started by: girish.batra
6 Replies
6. Solaris
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies
7. Solaris
I have JNI FCE-6460-N fc card , it is detected in OK prompt.....I connected Sun StorEDGE A5000 FC storage.
in OK prompt, PROBE-SCSI-ALL
showing A5000 fc hdds details in ok prompt.....
but in OS level.....not showing the hdd, i tried in DEVFSADM command and FORMAT command not showing A5000... (3 Replies)
Discussion started by: anysystem
3 Replies
8. Red Hat
Hi,
How to determine if HBA card in getting faulty from linux host ? any pointers. (2 Replies)
Discussion started by: saurabh84g
2 Replies
9. Solaris
please find the below o/p for your reference
bash-3.00# fcinfo hba-port
HBA Port WWN: 21000024ff295a34
OS Device Name: /dev/cfg/c2
Manufacturer: QLogic Corp.
Model: 375-3356-02
Firmware Version: 05.03.02
FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies
10. Solaris
Dear all,
I have a new Oracle Blade X4-2B server, running Solaris 10.
The server comes with a HBA card that will not be used now. It has not fibers connected to it. As a consequence, its leds never stop flashing.
My question is: how to disable this HBA card, without removing it physically... (2 Replies)
Discussion started by: Gus1971
2 Replies
LEARN ABOUT DEBIAN
transcalc
transcalc(1) General Commands Manual transcalc(1)
NAME
transcalc -- analysis and synthesis tool for microwave and RF transmsision lines
SYNOPSIS
transcalc [-h/--help] [-v/--version]
DESCRIPTION
transcalc is an analysis and synthesis tool for calculating the electrical and physical properties of different kinds of RF and microwave
transmission lines.
Transcalc allows you to interactively edit substrate, component, physical and electrical parameters of a given transmission line. For each
type of transmission line, using entry boxes, you can enter values for the various parameters, and either calculate its electrical proper-
ties (press Analyze button or function key F3), or use the given electrical requirements to sythesize (press Synthesize button or function
key F4) physical parameters of the required transmission line.
When run for the first time Transcalc creates a .transcalc directory under the user's home directory, where some configuration infor-
mation is stored. Transcalc remembers the last transmission line parameters used when the user exits and presents those parameters when
restarted.
Calculated results are updated and presented within the user interface. Moving the mouse over the parameter labels pops up a more helpful
tooltip about that parameter. For example, if you wonder what "Er" stands for, move the mouse over it and a helpful tooltip tells you that
it stands for relative permittivity.
Transcalc knows and converts between many unit types for length, frequency, resistance and angles. Default units can be saved by using the
File->Options menu. Calculated results include conductor and dielectric losses in decibels (dB).
OPTIONS
Transcalc has few command line options at this point.
-v, --version
Causes transcalc to print its version number (a string on the form MAJOR.MINOR, like 0.10) to the standard output, and then
exit.
AUTHOR
transcalc was written by Gopal Narayanan (gopal@astro.umass.edu) and Claudio Girardi (claudio.girardi@ieee.org). transcalc is available at
http://transcalc.sourceforge.net/ (link to URL http://transcalc.sourceforge.net/) .
transcalc(1)