Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
Hi All,
SUN emulex HBA card has been installed on P520 box.
When i run the cfgmgr i am getting the following message.
lpar2#cfgmgr
cfgmgr: 0514-621 WARNING: The following device packages are required for
device support but are not currently installed.... (0 Replies)
I have one 4GB, dual port HBA. Is each port rated for 4GB, or is it the whole HBA rated for 4GB?
Also, how do I determine which is port0 / port1 with "lscfg -vl fcs0" command. Thanks. (0 Replies)
I understand that fcinfo hba-port should show information(WWN, HBA vendor, etc..) but my result show "No adapter found". If I used grep -i 'version' /var/adm/messages* then I see my installed HBA (QLogic FCode at 2.00.09).. I am wondering why and what I had failed to install?
Thanks in advance.... (23 Replies)
Hi Gurus
I need to know few things related to HBA port & fcinfo command
I have a server where there are 4 HBA ports cards are their. Out of 4 ports 2 are in use & 2 are not in use when I check it physicall. Now I want to know the command through which I can get information about all above... (6 Replies)
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
I have JNI FCE-6460-N fc card , it is detected in OK prompt.....I connected Sun StorEDGE A5000 FC storage.
in OK prompt, PROBE-SCSI-ALL
showing A5000 fc hdds details in ok prompt.....
but in OS level.....not showing the hdd, i tried in DEVFSADM command and FORMAT command not showing A5000... (3 Replies)
Dear all,
I have a new Oracle Blade X4-2B server, running Solaris 10.
The server comes with a HBA card that will not be used now. It has not fibers connected to it. As a consequence, its leds never stop flashing.
My question is: how to disable this HBA card, without removing it physically... (2 Replies)
Discussion started by: Gus1971
2 Replies
LEARN ABOUT MOJAVE
locale::codes::langext
Locale::Codes::LangExt(3pm) Perl Programmers Reference Guide Locale::Codes::LangExt(3pm)NAME
Locale::Codes::LangExt - standard codes for language extension identification
SYNOPSIS
use Locale::Codes::LangExt;
$lext = code2langext('acm'); # $lext gets 'Mesopotamian Arabic'
$code = langext2code('Mesopotamian Arabic'); # $code gets 'acm'
@codes = all_langext_codes();
@names = all_langext_names();
DESCRIPTION
The "Locale::Codes::LangExt" module provides access to standard codes used for identifying language extensions, such as those as defined in
the IANA language registry.
Most of the routines take an optional additional argument which specifies the code set to use. If not specified, the default IANA language
registry codes will be used.
SUPPORTED CODE SETS
There are several different code sets you can use for identifying language extensions. A code set may be specified using either a name, or
a constant that is automatically exported by this module.
For example, the two are equivalent:
$lext = code2langext('acm','alpha');
$lext = code2langext('acm',LOCALE_LANGEXT_ALPHA);
The codesets currently supported are:
alpha
This is the set of three-letter (lowercase) codes from the IANA language registry, such as 'acm' for Mesopotamian Arabic.
This is the default code set.
ROUTINES
code2langext ( CODE [,CODESET] )
langext2code ( NAME [,CODESET] )
langext_code2code ( CODE ,CODESET ,CODESET2 )
all_langext_codes ( [CODESET] )
all_langext_names ( [CODESET] )
Locale::Codes::LangExt::rename_langext ( CODE ,NEW_NAME [,CODESET] )
Locale::Codes::LangExt::add_langext ( CODE ,NAME [,CODESET] )
Locale::Codes::LangExt::delete_langext ( CODE [,CODESET] )
Locale::Codes::LangExt::add_langext_alias ( NAME ,NEW_NAME )
Locale::Codes::LangExt::delete_langext_alias ( NAME )
Locale::Codes::LangExt::rename_langext_code ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangExt::add_langext_code_alias ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangExt::delete_langext_code_alias ( CODE [,CODESET] )
These routines are all documented in the Locale::Codes::API man page.
SEE ALSO
Locale::Codes
The Locale-Codes distribution.
Locale::Codes::API
The list of functions supported by this module.
http://www.iana.org/assignments/language-subtag-registry
The IANA language subtag registry.
AUTHOR
See Locale::Codes for full author history.
Currently maintained by Sullivan Beck (sbeck@cpan.org).
COPYRIGHT
Copyright (c) 2011-2013 Sullivan Beck
This module is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.18.2 2013-11-04 Locale::Codes::LangExt(3pm)