02-20-2011
jgt Thanks, However, the only close information close to this is IDE/SATA and i juggle the CMos dma/ultima value i got the same result "hd: no root hard disk controller was found hd: a boot time loadable driver may be required" as part of the hwconfig i saw %udi - udi environment
and ha=0 type=usb_msto UDI SCSI HBA
please help
10 More Discussions You Might Find Interesting
1. IP Networking
I have certain problems while Installing UNIX OPENSERVER.Could anyone solve that if I provide that problem. (3 Replies)
Discussion started by: Rajraius
3 Replies
2. UNIX for Advanced & Expert Users
I am doing some work for a customer that is running SCO 5.0.2 openserver and they have lost their cd. Is there anyplace I can download it? I have a replacement being shipped but it will not be here for two days and they are down. Any ideals? (3 Replies)
Discussion started by: SCOoT
3 Replies
3. UNIX for Dummies Questions & Answers
Hi guys,
I just got this new 6.0 version and i'm trying to setup a remote office to telnet to this server running sco 6.0, in previous version all i have to do is add this file under /etc/rc2.d call S99route and put the gate in that file and that was it, for some reason in 6.0 it does not... (1 Reply)
Discussion started by: josramon
1 Replies
4. SCO
Hi everyone,
We r installing sco openserver 5.07 on dell poweredge 2800 but we are facing problem when installing SCSI-raid drivers. Dell provide Perc4 raid card and we dont found raid drivers for this specific raid card. So we r stuck up on primary stage and we also dont know the... (2 Replies)
Discussion started by: mineshkoli
2 Replies
5. SCO
we are installing Openserver 5.0.7, system have SAS controller (Hard Disk Attached) as well as Adaptec ultra 320 controller (Tape Drive Attached).
At the time of installation we link both driver BTLD
Boot: Defbootstr link=accraid ad320
Aftes succesfully installation of accraid btld... (6 Replies)
Discussion started by: hafizurr
6 Replies
6. SCO
I'm trying to install openserver 6.0 on a locally assembled ACPI Multiprocessor PC with an intel core 2 dou e4400 @ 2 ghx and a WD8000JD SATA HD. Immediately after the startup screen I get "PANIC: kernel-mode address fault on kernel address 0xf000ff53". I get this message even if the drive is... (1 Reply)
Discussion started by: tvmccorm
1 Replies
7. SCO
can not for the life of me workout which BTLD to load allways shows no HDD available can any one give me a clue
tried
hpsas
aacraid
lsil
a160
a320
server is a ML310 G4 ?????:confused::confused: (7 Replies)
Discussion started by: wildginger
7 Replies
8. SCO
hello, i want to install release 5.0.5 on my notebook but the system hangs when extracing files from source media in fact after configuration all of setting please help me:confused: (1 Reply)
Discussion started by: hossein
1 Replies
9. UNIX for Advanced & Expert Users
Hi:
I'm installing SCO Open Server 6.0v on VMWare ESXi,
The instalation procedure giving by UnXis is using OVF deploy template and
it create a primary partition of 10gb only.
Any one know, if the OVF template could be edited to create a larger partition??
Thanks (0 Replies)
Discussion started by: Ccarballo
0 Replies
10. SCO
Hello all,
First off- great forum! I have learned a lot just by reading some of the questions and answers. Good to see there are good people out there still willing to help!
Here is my dilemma- I have a fairly new server running an Activant product on it, which runs SCO openserver 5.0.5... (9 Replies)
Discussion started by: crt001
9 Replies
LEARN ABOUT DEBIAN
halevt-mount
HALEVT-MOUNT(1) General Commands Manual HALEVT-MOUNT(1)
NAME
halevt-mount/halevt-umount - Mount or umount device through HAL
SYNOPSIS
halevt-mount [options] [-w] mountpoint|device|udi
halevt-mount [options] <-c | -r> <-a | mountpoint | device | udi>
halevt-mount [options] <-l | -s>
halevt-umount [options] < -a | mountpoint | device | udi>
DESCRIPTION
halevt-mount Mount or umount device through HAL and keep a track of devices handled. When called as halevt-umount the default is to
unmount, when called as halevt-mount the default is to mount. Option -c, -l, -r, -s or -w changes the operation performed. Additional
argument is considered to be a mount point, a device or an udi when unmounting or removing.
If the commands are not called with -s after changes in the state of the devices (after mounting, unmounting, removing devices), the infor-
mation available for halevt-mount and halevt-umount may become out of sync with the state of the system.
When run as user halevt (or as root), no uid= argument is passed to HAL when mounting, otherwise this option is passed, if the filesystem
allows it.
OPTIONS
-a When listing, list all the existing devices. For the other operations, perform the operation on all the handled devices.
-c Remove the handled device.
-d device
Use device device.
-f file
Use file file to store information about the handled devices instead of the default.
-h Help message and options summary.
-i directory
Use lock file and device information file in the directory directory (if they are not already specified).
-l List handled devices. Formatted with, on each line, udi:device:mountpoint.
-p mountpoint
Use mountpoint mountpoint.
-m umask
Set mount umask to umask if run as a system user, and the filesystem supports it.
-n file
Use file file as lock file.
-o option
Add the option option to the mount call.
-r Umount.
-s Sync the information about the handled devices with the informations known by HAL.
-u udi Use udi udi.
-w Add to the handled devices.
SEE ALSO
halevt(1), gnome-mount(1), pmount(1)
VERSION
This is halevt-mount version 0.1.6.2.
AUTHOR
Main author is Patrice Dumas pertusus at free dot fr.
AVAILABILITY
The latest version of this program can be found at:
http://www.nongnu.org/halevt/
COPYRIGHT
Copyright (C) 2007-2008 Patrice Dumas <pertusus at free dot fr>,
There is NO warranty. You may redistribute this software under the terms of the GNU General Public License; either version 2 of the
License, or (at your option) any later version. For more information about these matters, see the file named COPYING.
7th Edition HALEVT-MOUNT(1)