02-17-2011
Looking at the specs for the machine, I don't see why it shouldn't install. Check the CMOS to see if the SATA drive is set to legacy. The Broadcom network card might work, or you may have to install the Intel card.
10 More Discussions You Might Find Interesting
1. IP Networking
I have certain problems while Installing UNIX OPENSERVER.Could anyone solve that if I provide that problem. (3 Replies)
Discussion started by: Rajraius
3 Replies
2. UNIX for Advanced & Expert Users
I am doing some work for a customer that is running SCO 5.0.2 openserver and they have lost their cd. Is there anyplace I can download it? I have a replacement being shipped but it will not be here for two days and they are down. Any ideals? (3 Replies)
Discussion started by: SCOoT
3 Replies
3. UNIX for Dummies Questions & Answers
Hi guys,
I just got this new 6.0 version and i'm trying to setup a remote office to telnet to this server running sco 6.0, in previous version all i have to do is add this file under /etc/rc2.d call S99route and put the gate in that file and that was it, for some reason in 6.0 it does not... (1 Reply)
Discussion started by: josramon
1 Replies
4. SCO
Hi everyone,
We r installing sco openserver 5.07 on dell poweredge 2800 but we are facing problem when installing SCSI-raid drivers. Dell provide Perc4 raid card and we dont found raid drivers for this specific raid card. So we r stuck up on primary stage and we also dont know the... (2 Replies)
Discussion started by: mineshkoli
2 Replies
5. SCO
we are installing Openserver 5.0.7, system have SAS controller (Hard Disk Attached) as well as Adaptec ultra 320 controller (Tape Drive Attached).
At the time of installation we link both driver BTLD
Boot: Defbootstr link=accraid ad320
Aftes succesfully installation of accraid btld... (6 Replies)
Discussion started by: hafizurr
6 Replies
6. SCO
I'm trying to install openserver 6.0 on a locally assembled ACPI Multiprocessor PC with an intel core 2 dou e4400 @ 2 ghx and a WD8000JD SATA HD. Immediately after the startup screen I get "PANIC: kernel-mode address fault on kernel address 0xf000ff53". I get this message even if the drive is... (1 Reply)
Discussion started by: tvmccorm
1 Replies
7. SCO
can not for the life of me workout which BTLD to load allways shows no HDD available can any one give me a clue
tried
hpsas
aacraid
lsil
a160
a320
server is a ML310 G4 ?????:confused::confused: (7 Replies)
Discussion started by: wildginger
7 Replies
8. SCO
hello, i want to install release 5.0.5 on my notebook but the system hangs when extracing files from source media in fact after configuration all of setting please help me:confused: (1 Reply)
Discussion started by: hossein
1 Replies
9. UNIX for Advanced & Expert Users
Hi:
I'm installing SCO Open Server 6.0v on VMWare ESXi,
The instalation procedure giving by UnXis is using OVF deploy template and
it create a primary partition of 10gb only.
Any one know, if the OVF template could be edited to create a larger partition??
Thanks (0 Replies)
Discussion started by: Ccarballo
0 Replies
10. SCO
Hello all,
First off- great forum! I have learned a lot just by reading some of the questions and answers. Good to see there are good people out there still willing to help!
Here is my dilemma- I have a fairly new server running an Activant product on it, which runs SCO openserver 5.0.5... (9 Replies)
Discussion started by: crt001
9 Replies
MFI(4) BSD Kernel Interfaces Manual MFI(4)
NAME
mfi -- LSI MegaRAID SAS driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device pci
device mfi
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
mfi_load="YES"
DESCRIPTION
This driver is for LSI's next generation PCI Express SAS RAID controllers. Access to RAID arrays (logical disks) from this driver is pro-
vided via /dev/mfid? device nodes. A simple management interface is also provided on a per-controller basis via the /dev/mfi? device node.
The mfi name is derived from the phrase "MegaRAID Firmware Interface", which is substantially different than the old "MegaRAID" interface and
thus requires a new driver. Older SCSI and SATA MegaRAID cards are supported by amr(4) and will not work with this driver.
Two sysctls are provided to tune the mfi driver's behavior when a request is made to remove a mounted volume. By default the driver will
disallow any requests to remove a mounted volume. If the sysctl dev.mfi.%d.delete_busy_volumes is set to 1, then the driver will allow
mounted volumes to be removed.
A tunable is provided to adjust the mfi driver's behaviour when attaching to a card. By default the driver will attach to all known cards
with high probe priority. If the tunable hw.mfi.mrsas_enable is set to 1, then the driver will reduce its probe priority to allow mrsas to
attach to the card instead of mfi.
HARDWARE
The mfi driver supports the following hardware:
o LSI MegaRAID SAS 1078
o LSI MegaRAID SAS 8408E
o LSI MegaRAID SAS 8480E
o LSI MegaRAID SAS 9240
o LSI MegaRAID SAS 9260
o Dell PERC5
o Dell PERC6
o IBM ServeRAID M1015 SAS/SATA
o IBM ServeRAID M1115 SAS/SATA
o IBM ServeRAID M5015 SAS/SATA
o IBM ServeRAID M5110 SAS/SATA
o IBM ServeRAID-MR10i
o Intel RAID Controller SRCSAS18E
o Intel RAID Controller SROMBSAS18E
FILES
/dev/mfid? array/logical disk interface
/dev/mfi? management interface
DIAGNOSTICS
mfid%d: Unable to delete busy device An attempt was made to remove a mounted volume.
SEE ALSO
amr(4), pci(4), mfiutil(8)
HISTORY
The mfi driver first appeared in FreeBSD 6.1.
AUTHORS
The mfi driver and this manual page were written by Scott Long <scottl@FreeBSD.org>.
BUGS
The driver does not support big-endian architectures at this time.
BSD
July 15, 2013 BSD