Sponsored Content
Top Forums UNIX for Advanced & Expert Users Installation of Sco Openserver 5.0.7 on HP DC 7600 Post 302497715 by jgt on Thursday 17th of February 2011 08:54:04 PM
Old 02-17-2011
Looking at the specs for the machine, I don't see why it shouldn't install. Check the CMOS to see if the SATA drive is set to legacy. The Broadcom network card might work, or you may have to install the Intel card.
 

10 More Discussions You Might Find Interesting

1. IP Networking

Installation Problem in Unix Openserver

I have certain problems while Installing UNIX OPENSERVER.Could anyone solve that if I provide that problem. (3 Replies)
Discussion started by: Rajraius
3 Replies

2. UNIX for Advanced & Expert Users

SCO 5.0.2 openserver

I am doing some work for a customer that is running SCO 5.0.2 openserver and they have lost their cd. Is there anyplace I can download it? I have a replacement being shipped but it will not be here for two days and they are down. Any ideals? (3 Replies)
Discussion started by: SCOoT
3 Replies

3. UNIX for Dummies Questions & Answers

SCO Openserver 6.0

Hi guys, I just got this new 6.0 version and i'm trying to setup a remote office to telnet to this server running sco 6.0, in previous version all i have to do is add this file under /etc/rc2.d call S99route and put the gate in that file and that was it, for some reason in 6.0 it does not... (1 Reply)
Discussion started by: josramon
1 Replies

4. SCO

sco openserver 5.07 installation problem

Hi everyone, We r installing sco openserver 5.07 on dell poweredge 2800 but we are facing problem when installing SCSI-raid drivers. Dell provide Perc4 raid card and we dont found raid drivers for this specific raid card. So we r stuck up on primary stage and we also dont know the... (2 Replies)
Discussion started by: mineshkoli
2 Replies

5. SCO

SCO OpenServer 5.0.7 Installation problem

we are installing Openserver 5.0.7, system have SAS controller (Hard Disk Attached) as well as Adaptec ultra 320 controller (Tape Drive Attached). At the time of installation we link both driver BTLD Boot: Defbootstr link=accraid ad320 Aftes succesfully installation of accraid btld... (6 Replies)
Discussion started by: hafizurr
6 Replies

6. SCO

openserver 6.0 installation PANIC

I'm trying to install openserver 6.0 on a locally assembled ACPI Multiprocessor PC with an intel core 2 dou e4400 @ 2 ghx and a WD8000JD SATA HD. Immediately after the startup screen I get "PANIC: kernel-mode address fault on kernel address 0xf000ff53". I get this message even if the drive is... (1 Reply)
Discussion started by: tvmccorm
1 Replies

7. SCO

SCO OpenServer 5.0.7 Installation problem on HP ML310 G4

can not for the life of me workout which BTLD to load allways shows no HDD available can any one give me a clue tried hpsas aacraid lsil a160 a320 server is a ML310 G4 ?????:confused::confused: (7 Replies)
Discussion started by: wildginger
7 Replies

8. SCO

sco openserver release 5.0.5 installation problems on notebook

hello, i want to install release 5.0.5 on my notebook but the system hangs when extracing files from source media in fact after configuration all of setting please help me:confused: (1 Reply)
Discussion started by: hossein
1 Replies

9. UNIX for Advanced & Expert Users

OpenServer 6.0v installation

Hi: I'm installing SCO Open Server 6.0v on VMWare ESXi, The instalation procedure giving by UnXis is using OVF deploy template and it create a primary partition of 10gb only. Any one know, if the OVF template could be edited to create a larger partition?? Thanks (0 Replies)
Discussion started by: Ccarballo
0 Replies

10. SCO

Installation on SCO Openserver 5.0.5

Hello all, First off- great forum! I have learned a lot just by reading some of the questions and answers. Good to see there are good people out there still willing to help! Here is my dilemma- I have a fairly new server running an Activant product on it, which runs SCO openserver 5.0.5... (9 Replies)
Discussion started by: crt001
9 Replies
CARD(1) 								FSF								   CARD(1)

NAME
card - print reference card of program options SYNOPSIS
card [OPTION]... PROGRAM... DESCRIPTION
Print a reference card of the PROGRAMs thanks to their inline help. OPTIONS
-h, --help display this help and exit -v, --version display version information and exit -o, --output=FILE save the output in FILE -l, --language=LL print the help in the language LL (default: English) --command=CMD perform pretty-printing on the output of CMD (e.g. --command='netscape -help') Options for a2ps are given after `--', for instance $ card -lfr a2ps -- -Pdisplay -4 News, updates and documentation: http://www.inf.enst.fr/~demaille/a2ps/ AUTHOR
Written by Akim Demaille. REPORTING BUGS
Report bugs to <bug-a2ps@gnu.org>. COPYRIGHT
Copyright (C) 1997-99 Akim Demaille, Miguel Santana This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICU- LAR PURPOSE. SEE ALSO
a2ps(1), card(1), fixps(1), pdiff(1), psset(1), texi2dvi4a2ps(1). The full documentation for card is maintained as a Texinfo manual. If the info and card programs are properly installed at your site, the command info card should give you access to the complete manual. card 1.3 (GNU a2ps 4.13) February 2000 CARD(1)
All times are GMT -4. The time now is 08:29 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy