Sponsored Content
Operating Systems AIX AIX 5.3 Boot Hangs On Power4 Hardware Post 302496962 by a_sim on Tuesday 15th of February 2011 09:47:40 PM
Old 02-15-2011
@aix_guy: the machine type is 7029-6e3. This machine is not and was never attached to a HMC.

@zxmaus: I went into SMS mode to select the console. Manage to do that by pressing "3". After that it started to boot again and automatically went back into SMS mode. But few days back when I selected the console, right after that it went back to the main SMS menu. The only thing change I did to the machine was unplug the network cable.
 

10 More Discussions You Might Find Interesting

1. AIX

AIX Hangs

Hai I am new to AIX, currently in our shop we use AIX 4.3.3 , where we have hosted the websphere 3.5 applicaiton on it. The AIX server is getting hanged very frequently, when analyse we found the swap memory is increasing once it reaches the memory 100 the system is totaly in hung state, so... (5 Replies)
Discussion started by: vipin77
5 Replies

2. AIX

AIX 5.1 POWER4 support help

Can anyone let me know the output of command 'uname -aL' on AIX 5.1 POWER4 support? (6 Replies)
Discussion started by: arnab84
6 Replies

3. AIX

RS6K B50 Hangs at E140 on Boot

I've got an RS6K B50, and i've installed AIX 5.3, TL5. It installs fine, the only customisations i make to the BOS are to change the locale / keyboard layout to UK, and to choose not to install graphical software. I have no video card in this box, and i connect via a serial console (null modem... (4 Replies)
Discussion started by: craigp84
4 Replies

4. Solaris

Boot hangs up on solaris

Hi all, I have a SUN server Sun-Fire-V890 running solaris 9, with a remote system console . Both the IP adresses of the server and the console are in a private network (address 10.67.xxx). For some reasons I need to give the access to the server from outside address 194.xxx, but I prefer that... (2 Replies)
Discussion started by: aribault
2 Replies

5. AIX

AIX hangs on boot

Hi guys, Got a tiny bit of a problem on one of our servers here at work. I installed AIX 5.3 on the server and that went fine. Then I upgraded to ML 5300-05-01, but now the system just hangs on boot. The system starts up and the monitor comes on in few minutes, but a few seconds later when... (6 Replies)
Discussion started by: drchris
6 Replies

6. AIX

AIX hangs through the boot process

To All: I have this AIX machine (see boot process below). The problem was it hangs at: The ctrmc Subsystem has been started. Subsystem PID is 11906.. I checked with other forums but their advise were just "strong punches in the air" with no specific explanation. I really appreciate if... (6 Replies)
Discussion started by: aix_xia
6 Replies

7. Ubuntu

Boot hangs while adding swap

Boot process hangs after reaching the following line: Adding 5853176k swap on /dev/mapper/mch-swap_1. Priority:-1 extents:1 across:5853176kUsing knoppix 6.2 as LiveCD, and mounting the partitions, I got the following: # /etc/fstab: static file system information. # # Use 'blkid -o value -s... (0 Replies)
Discussion started by: fzaker
0 Replies

8. Solaris

All Hardware information in Ok Boot Prompt

Can anyone tell me the command to check all the hardware information in Ok boot Prompt. Like the hard disk space memory size ..... (3 Replies)
Discussion started by: newbi8321
3 Replies

9. Solaris

Server Hangs at boot

Hi Guys, I have a SunBlade 1500 which I use to practice at home. Suddenly when I power on the server it just displays the solaris banner and Boot device: disk File and args: Then it stops and says " rebooting with command: boot" It doesn't boot to the kernel. Is there anyway I can possibly... (5 Replies)
Discussion started by: cjashu
5 Replies

10. Solaris

Solaris 10 - hangs during boot

Power server up runs through diagnostics. Goes to the boot section and then the bit where the cursor is spinning and thats it. Hangs completely. Any ideas? (10 Replies)
Discussion started by: psychocandy
10 Replies
cvcd(1M)                                                  System Administration Commands                                                  cvcd(1M)

NAME
cvcd - virtual console daemon SYNOPSIS
/platform/platform_name/cvcd DESCRIPTION
The virtual console daemon, cvcd, is a server process that supports the network console provided on some platforms. The cvcd daemon accepts network console connections from a remote host (only one host at any given time). Console input is read from this connection and forwarded to cvc(7D) by way of cvcredir(7D). Similarly, console output is read from cvcredir(7D) and forwarded across the network console connection. If cvcd dies, console traffic is automatically rerouted through an internal hardware interface. The cvcd daemon normally starts at system boot time. Each domain supports only one cvcd process at a time. Caution: On Sun Enterprise 10000 domains, cvcd uses a configuration file (/etc/ssphostname) to determine the name of the host from which network console connections are allowed. If the remote console host is renamed, you must edit the configuration file to reflect that change. OPERANDS
The following operands are supported: platform_name The official Sun platform name used in packaging and code. For example, for Sun Fire 15K servers, the platform_name would be SUNW,Sun-Fire-15000. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Architecture |Sun Enterprise 10000 | | |servers, Sun Fire High-End | | |Systems | +-----------------------------+-----------------------------+ |Availability |SUNWcvc.u | +-----------------------------+-----------------------------+ SEE ALSO
svcs(1), svcadm(1M), services(4), attributes(5), smf(5), cvc(7D), cvcredir(7D) Sun Enterprise 10000 SSP Reference Manual System Management Services (SMS) Reference Manual NOTES
The cvcd service is managed by the service management facility, smf(5), under the service identifier: svc:/system/cvc Administrative actions on this service, such as enabling, disabling, or requesting restart, can be performed using svcadm(1M). The ser- vice's status can be queried using the svcs(1) command. SunOS 5.10 11 Aug 2004 cvcd(1M)
All times are GMT -4. The time now is 09:41 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy