Hi,
Here is my piece of code used with sed in shell script:
The problem that i am facing with the above is that in 'myxml' file i have mulitple instances of
so when i execute the above sed command, it is appending the
after every instance of
Please can some one help me to know if there is a way where i can append the text only after the first instance of the
and not after every instance of the
Thanks
Hi, I've been trying to figure this one out and found a post about this on the forum here but the solution didn't seem to work for me. Basically what I have is a file that looks something like:
stuff
morestuff
0
otherthing
0
etc
I want to substitute for the 0 but what I want to... (9 Replies)
hi
i have one file where i want to substitute only first instance of
swap
with swap1
i want to replcae only first instance of swap in my script
i know we can do this with awk. but i need to do this with sed only
i tried follwoing code
sed 's/swap/swap1' filename
but here all... (15 Replies)
I need to reduce a file's size below 50MB by deleting chucks of text. The following sed does this.
sed '/^begpattern/,/endpattern/d' myfile
However, it's possible that the file size can get below 50MB by just deleting the first instance of the pattern. How do I code that into sed?
Or can awk... (8 Replies)
I was told a way to do this with awk earlier today but is there a way with sed to specify the last instance of a character on a line?
You will know what character you're looking for but there could be none or one hundred instances of it on a line say and you ONLY want to specify the last one for... (3 Replies)
Hello,
There is a log file A.log where new lines are getting added every minute.
When ever any new lines are getting added in to A , the same lines needs to be appended to B.log
I need to append these newly added lines to end of another file B through a shell script. I tried CAT but its... (2 Replies)
Hi All
I need help
am having a source file as below
emp
dept
class
subclass
region
country
division
first i need to get line count and i need to divide by 3 it is an parameter passing value
number of lines 7 (8 Replies)
The following text is in testFile.txt:
one 5
two 10
three 15
four 20
five 25
six 10
seven 35
eight 10
nine 45
ten 50
I'd like to use sed to print the first occurance of search pattern /10/ in a given range. This command is to be run against large log files, so to optimize efficiency,... (9 Replies)
Hi all,
I'm new to the forum and also relatively new to sed and other such wonderfully epic tools.
I'm attempting to grab a section of text between two words, but it seems to match all instances of the range instead of stopping at just the first.
This occurs when I use:
sed -n... (7 Replies)
Discussion started by: Lazarix
7 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)