Sponsored Content
Operating Systems AIX AIX 5.3 Boot Hangs On Power4 Hardware Post 302495717 by johnf on Friday 11th of February 2011 02:55:16 AM
Old 02-11-2011
Quote:
Originally Posted by a_sim
Hi all,

We have a old Power4 server with AIX version 5.3 installed. Upon boot up, it hangs right after the AIX welcome screen. On the diagnostic load progress LED indicator, I saw that it stopped at '0c32' then after awhile the LED would be blank. The screen on the monitor will hang at the black terminal screen with a not blinking cursor.

What should I do next? I hope the filesystem is not corrupted fingers crossed.

Thanks.
How is the terminal connected? The code you are getting is a standard O/S output which is saying the terminal has been found (c32 A direct-attached display (HFT) was selected.) Is there a graphics adapter fitted? You could try disconnecting the display and connecting a serial display to either S1 or S2 to see if you get the login screen.

I cannot give any further advice as a 0C32 is the normal end to the boot sequence so you problems should be with the display.

I hope this helps.
 

10 More Discussions You Might Find Interesting

1. AIX

AIX Hangs

Hai I am new to AIX, currently in our shop we use AIX 4.3.3 , where we have hosted the websphere 3.5 applicaiton on it. The AIX server is getting hanged very frequently, when analyse we found the swap memory is increasing once it reaches the memory 100 the system is totaly in hung state, so... (5 Replies)
Discussion started by: vipin77
5 Replies

2. AIX

AIX 5.1 POWER4 support help

Can anyone let me know the output of command 'uname -aL' on AIX 5.1 POWER4 support? (6 Replies)
Discussion started by: arnab84
6 Replies

3. AIX

RS6K B50 Hangs at E140 on Boot

I've got an RS6K B50, and i've installed AIX 5.3, TL5. It installs fine, the only customisations i make to the BOS are to change the locale / keyboard layout to UK, and to choose not to install graphical software. I have no video card in this box, and i connect via a serial console (null modem... (4 Replies)
Discussion started by: craigp84
4 Replies

4. Solaris

Boot hangs up on solaris

Hi all, I have a SUN server Sun-Fire-V890 running solaris 9, with a remote system console . Both the IP adresses of the server and the console are in a private network (address 10.67.xxx). For some reasons I need to give the access to the server from outside address 194.xxx, but I prefer that... (2 Replies)
Discussion started by: aribault
2 Replies

5. AIX

AIX hangs on boot

Hi guys, Got a tiny bit of a problem on one of our servers here at work. I installed AIX 5.3 on the server and that went fine. Then I upgraded to ML 5300-05-01, but now the system just hangs on boot. The system starts up and the monitor comes on in few minutes, but a few seconds later when... (6 Replies)
Discussion started by: drchris
6 Replies

6. AIX

AIX hangs through the boot process

To All: I have this AIX machine (see boot process below). The problem was it hangs at: The ctrmc Subsystem has been started. Subsystem PID is 11906.. I checked with other forums but their advise were just "strong punches in the air" with no specific explanation. I really appreciate if... (6 Replies)
Discussion started by: aix_xia
6 Replies

7. Ubuntu

Boot hangs while adding swap

Boot process hangs after reaching the following line: Adding 5853176k swap on /dev/mapper/mch-swap_1. Priority:-1 extents:1 across:5853176kUsing knoppix 6.2 as LiveCD, and mounting the partitions, I got the following: # /etc/fstab: static file system information. # # Use 'blkid -o value -s... (0 Replies)
Discussion started by: fzaker
0 Replies

8. Solaris

All Hardware information in Ok Boot Prompt

Can anyone tell me the command to check all the hardware information in Ok boot Prompt. Like the hard disk space memory size ..... (3 Replies)
Discussion started by: newbi8321
3 Replies

9. Solaris

Server Hangs at boot

Hi Guys, I have a SunBlade 1500 which I use to practice at home. Suddenly when I power on the server it just displays the solaris banner and Boot device: disk File and args: Then it stops and says " rebooting with command: boot" It doesn't boot to the kernel. Is there anyway I can possibly... (5 Replies)
Discussion started by: cjashu
5 Replies

10. Solaris

Solaris 10 - hangs during boot

Power server up runs through diagnostics. Goes to the boot section and then the bit where the cursor is spinning and thats it. Hangs completely. Any ideas? (10 Replies)
Discussion started by: psychocandy
10 Replies
DISPLAYS(5)                                                     File Formats Manual                                                    DISPLAYS(5)

NAME
displays - Display Configuration File DESCRIPTION
The interactive graphics programs Caesar, Magic, and Gremlin use two separate terminals: a text terminal from which commands are issued, and a color graphics terminal on which graphical output is displayed. These programs use a displays file to associate their text terminal with its corresponding display device. The displays file is an ASCII text file with one line for each text terminal/graphics terminal pair. Each line contains 4 items separated by spaces: the name of the port attached to a text terminal, the name of the port attached to the associated graphics terminal, the phos- phor type of the graphics terminal's monitor, and the type of graphics terminal. An applications program may use the phosphor type to select a color map tuned to the monitor's characteristics. Only the std phosphor type is supported at UC Berkeley. The graphics terminal type specifies the device driver a program should use when communicating with its graphics terminal. Magic supports types UCB512, AED1024, and SUN120. Other programs may recognize different display types. See the manual entry for your specific applica- tion for more information. A sample displays file is: /dev/ttyi1 /dev/ttyi0 std UCB512 /dev/ttyj0 /dev/ttyj1 std UCB512 /dev/ttyjf /dev/ttyhf std UCB512 /dev/ttyhb /dev/ttyhc std UCB512 /dev/ttyhc /dev/ttyhb std UCB512 (R) In this example, /dev/ttyi1 connects to a text terminal. An associated UCB512 graphics terminal with standard phosphor is connected to /dev/ttyi0. FILES
Magic uses the displays file ~cad/lib/displays. Gremlin looks in /usr/local/displays. SEE ALSO
magic(1) 3rd Berkeley Distribution 2/19/85 DISPLAYS(5)
All times are GMT -4. The time now is 08:44 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy