02-08-2011
If you want zones to communicate through an external gateway, use exclusive IP zones, not shared IP ones. When using shared IP like you do, there is a single IP stack shared by all zones. That means there is no chance for a packet to leave the server if its destination address is local. This is by design and by standard.
9 More Discussions You Might Find Interesting
1. Solaris
Hi,
I have a problem with a server disconnecting from the network.
This is a SUN box with dual NIC's running Solaris 8.
We have a Nokia router that routes traffic but it's virtual address doesn't respond to pings. When the SUN box sends out a ping, if nothing comes back it will shut down... (5 Replies)
Discussion started by: m_smith
5 Replies
2. AIX
OS: AIX 6.1
The host has a dual port NIC installed and when I went to run `cfgmgr -v` to configure it I got an error showing device packages are missing from the install:
`cfgmgr -v` on 10.15.xx.xxx
cfgmgr: 0514-621 WARNING: The following device packages are required for device support but... (3 Replies)
Discussion started by: b1f30
3 Replies
3. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
4. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
5. Solaris
Hi all,
I'm having some trouble identifying what route is being used to talk to a target host. I can figure it out by looking at the routing tables but I want to automate this and don't much feel like scripting the network mask logic when I'd think there'd be a way to have the OS do it for me.... (5 Replies)
Discussion started by: Smiling Dragon
5 Replies
6. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
7. Solaris
Dear,
I hope you all will be ok.
I have an issue with Solaris box running on x86 Blade.
I am unable to ping a node neither traceroute. I am able to do traceroute from oce0:6 port which have IP and subnet of same type which oce0:1 has.
details are as follows:
Problem:
root@rinams02:/#... (3 Replies)
Discussion started by: khaniqshahid
3 Replies
8. Solaris
Hi All
Kindly let me know how can I move Solaris 10 OS running update 10 on physical machine to another machine solaris zone running Solaris 10 update 11 (2 Replies)
Discussion started by: amity
2 Replies
9. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies