Mulitple Zones on Dual NIC host Post: 302494747

9 More Discussions You Might Find Interesting

1. Solaris

Dual NIC problem

Hi, I have a problem with a server disconnecting from the network. This is a SUN box with dual NIC's running Solaris 8. We have a Nokia router that routes traffic but it's virtual address doesn't respond to pings. When the SUN box sends out a ping, if nothing comes back it will shut down...

2. AIX

Dual port NIC, cfgmgr

OS: AIX 6.1 The host has a dual port NIC installed and when I went to run `cfgmgr -v` to configure it I got an error showing device packages are missing from the install: `cfgmgr -v` on 10.15.xx.xxx cfgmgr: 0514-621 WARNING: The following device packages are required for device support but...

3. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux...

4. IP Networking

squid proxy: one NIC for inbound & one NIC for outbound?

I am new in squid proxy. My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)? Thank you in advance!

5. Solaris

How can I find which NIC is used to talk to a given host (except traceroute)

Hi all, I'm having some trouble identifying what route is being used to talk to a target host. I can figure it out by looking at the routing tables but I want to automate this and don't much feel like scripting the network mask logic when I'd think there'd be a way to have the OS do it for me....

6. Red Hat

I want to tune NIC's rps, rfs and xps value. which NIC device should I modify.

Dear All I want tune my NIC's rps, rfs and xps value. In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1). Here is the question? Which device should I modify ? eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0) Any advice is welcome....

7. Solaris

Network issue on multinic. Unable to ping a host from One NIC but other works

Dear, I hope you all will be ok. I have an issue with Solaris box running on x86 Blade. I am unable to ping a node neither traceroute. I am able to do traceroute from oce0:6 port which have IP and subnet of same type which oce0:1 has. details are as follows: Problem: root@rinams02:/#...

8. Solaris

Migration of Solaris 10 on physical host to Solaris Zones

Hi All Kindly let me know how can I move Solaris 10 OS running update 10 on physical machine to another machine solaris zone running Solaris 10 update 11

9. Linux

Add two different subnet public IPs to single NIC or two different NIC on same box

Hello Admins, My ask is how can I add two different subnet IPs to same box with two different gateways? The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware. How can I get connected...

LEARN ABOUT SUNOS

install-solaris

install-solaris(1M)													       install-solaris(1M)

NAME

       install-solaris - install the Solaris operating system

SYNOPSIS

       install-solaris

       install-solaris	invokes  the  Solaris  Install	program. Depending on graphical capability and available memory at the time of invocation,
       install-solaris invokes either a text-based installer or a graphical installer.

       The following minimum requirements for physical memory dictate which features are available during installation:

       For SPARC machines:

       128 MB

	   Minimum physical memory for all installation types

       128 MB

	   Minimum physical memory required for windowing system

       384 MB

	   Minimum physical memory required for graphical-based installation

       For x86 machines:

       256 MB

	   Minimum physical memory for all installation types

       256 MB

	   Minimum physical memory required for windowing system

       512 MB

	   Minimum physical memory required for graphical-based installation

       In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number  of  fea-
       tures available.

       install-solaris	exists	only  on  the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the  for more
       details.

       install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
       installation media. Refer to the  for disk space requirements.

       Refer to the  for more information on the various menus and selections.

       See attributes(5) for descriptions of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE	     |	    ATTRIBUTE VALUE	   |
       +-----------------------------+-----------------------------+
       |Availability		     |SUNWcdrom  (Solaris instal-  |
       |			     |lation media)		   |
       +-----------------------------+-----------------------------+
       |Interface Stability	     |Evolving			   |
       +-----------------------------+-----------------------------+

       pkginfo(1), install(1M), pkgadd(1M), attributes(5)

       It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.

								    23 Sep 2005 					       install-solaris(1M)