I had a power failure the other day and when my relatively new Solaris 10 machine rebooted it is thrown into maintenance mode.
I've found the following lines in the /var/adm/messages file, I'm assuming this is the root cause of the problem. However, I don't have the slightest idea on how to... (9 Replies)
Hello All,
On solaris 10 server i could see the FTP service is in maintenance mode always :mad:
Could some assist?
svcs -xv
svc:/network/nfs/nlockmgr:default (NFS lock manager)
State: maintenance since Tue 28 Jul 2009 11:47:55 AM BST
Reason: Restarting too quickly.
See: Sun... (5 Replies)
Hi,
I have installed Hudson on a Solaris 11 server, using the installation instructions available at Paul Oswald: Hudson Solaris SMF Manifest.
When I perform svcs -l hudson, I get:
fmri svc:/application/hudson:default
name Hudson Continuous Build Server
enabled true... (4 Replies)
I have a Solaris 10 SunFire v880 machine and I'm having trouble with Samba.
Samba has worked on this machine but since the machine has been re-booted Samba has not worked.
Machine details are:
cat /etc/release
Solaris 10 10/08 s10s_u6wos_07b SPARC
Copyright 2008... (2 Replies)
:confused:
when i tried to look the status of DNS-client, it is in maintenance mode.....
Please tell me how to bring it back to online mode...PLEASE TELL ME STEP BY STEP.... PLEASE...
:wall: (2 Replies)
Hi experts,
This is a production server.
Host information's are below
SunOS hostname_srv 5.10 Generic_150400-09 sun4v sparc sun4v
Now issue with ntp service, This host have zone in it with 9 hosts, Every hosts have ntp service issue. While i check for the service status it's in... (3 Replies)
Hi this may be a easy question to answer but thanks in advance.
So I was able to download the VIOS media from IBM and currently I am burning it to a cd/dvd right now.
The steps I've collected so far are from the net. can you please confirm and add on to the steps if there are any steps... (0 Replies)
i booted into maintenance mode
boot -- -s
from the console
I got the
Root password for system maintenance (control-d to bypass)
I did control -d
and then logged in
it told me that I was booting into boot -s
but after I did a control -d and logged in
who -r shows
... (9 Replies)
Discussion started by: goya
9 Replies
LEARN ABOUT REDHAT
lpsched
lpsched(1M) System Administration Commands lpsched(1M)NAME
lpsched - start the LP print service
SYNOPSIS
lpsched [-f num_filters] [-n num_notifiers] [-p fd_limit] [-r reserved_fds]
DESCRIPTION
The lpsched command starts or restarts the LP print service.
The lpshut command stops the LP print service. Printers that are restarted using lpsched reprint (in their entirety) print requests that
were stopped by lpshut. See lpshut(1M).
It is recommended that you start and stop the LP print service using svcadm(1M). See NOTES.
OPTIONS
The following options are supported:
-f num_filters Specifies the number of concurrent slow filters that may be run on a print server. A default value of 1 is used if
none is specified. Depending on server configuration, a value of 1 may cause printers to remain idle while there
are jobs queued to them.
-n num_notifiers Specifies the number of concurrent notification processes that can run on a print server. A default value of 1 is
used when none is specified.
-p fd_limit Specifies the file descriptor resource limit for the lpsched process. A default value of 4096 is used if none is
specified. On extremely large and active print servers, it may be necessary to increase this value.
-r reserved_fds Specifies the number of file descriptors that the scheduler reserves for internal communications under heavy load.
A default value of 2 is used when none is specified. It should not be necessary to modify this value unless
instructed to do so when troubleshooting problems under high load.
EXIT STATUS
The following exit values are returned:
0 Successful completion.
non-zero An error occurred.
FILES
/var/spool/lp/* LP print queue.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWpsu |
+-----------------------------+-----------------------------+
SEE ALSO lp(1), svcs(1), lpstat(1), lpadmin(1M), lpmove(1M), lpshut(1M), svcadm(1M), attributes(5), smf(5)
System Administration Guide: Basic Administration
NOTES
The lpsched service is managed by the service management facility, smf(5), under the service identifier:
svc:/application/print/server
Administrative actions on this service, such as enabling, disabling, or requesting restart, can be performed using svcadm(1M). The ser-
vice's status can be queried using the svcs(1) command.
SunOS 5.10 3 Sep 2004 lpsched(1M)