01-30-2011
Stupid question possibly but did it ever work?
10 More Discussions You Might Find Interesting
1. Solaris
I had a power failure the other day and when my relatively new Solaris 10 machine rebooted it is thrown into maintenance mode.
I've found the following lines in the /var/adm/messages file, I'm assuming this is the root cause of the problem. However, I don't have the slightest idea on how to... (9 Replies)
Discussion started by: cheetobandito
9 Replies
2. Solaris
Hello All,
On solaris 10 server i could see the FTP service is in maintenance mode always :mad:
Could some assist?
svcs -xv
svc:/network/nfs/nlockmgr:default (NFS lock manager)
State: maintenance since Tue 28 Jul 2009 11:47:55 AM BST
Reason: Restarting too quickly.
See: Sun... (5 Replies)
Discussion started by: bullz26
5 Replies
3. Solaris
Hi,
I have installed Hudson on a Solaris 11 server, using the installation instructions available at Paul Oswald: Hudson Solaris SMF Manifest.
When I perform svcs -l hudson, I get:
fmri svc:/application/hudson:default
name Hudson Continuous Build Server
enabled true... (4 Replies)
Discussion started by: JVerstry
4 Replies
4. Solaris
I have a Solaris 10 SunFire v880 machine and I'm having trouble with Samba.
Samba has worked on this machine but since the machine has been re-booted Samba has not worked.
Machine details are:
cat /etc/release
Solaris 10 10/08 s10s_u6wos_07b SPARC
Copyright 2008... (2 Replies)
Discussion started by: KenLynch
2 Replies
5. Solaris
Hi Guys,
I have a sunblade 1500. I booted the system and it booted to maintenance mode. How can I fix this?
Thanks lots (8 Replies)
Discussion started by: cjashu
8 Replies
6. Solaris
:confused:
when i tried to look the status of DNS-client, it is in maintenance mode.....
Please tell me how to bring it back to online mode...PLEASE TELL ME STEP BY STEP.... PLEASE...
:wall: (2 Replies)
Discussion started by: vamshigvk475
2 Replies
7. Solaris
Hi,
I have an issue with RPC bind service and its failing with status 1. any help would be much appreciated.
THanks (2 Replies)
Discussion started by: Yakub Humami
2 Replies
8. Solaris
Hi experts,
This is a production server.
Host information's are below
SunOS hostname_srv 5.10 Generic_150400-09 sun4v sparc sun4v
Now issue with ntp service, This host have zone in it with 9 hosts, Every hosts have ntp service issue. While i check for the service status it's in... (3 Replies)
Discussion started by: babinlonston
3 Replies
9. AIX
Hi this may be a easy question to answer but thanks in advance.
So I was able to download the VIOS media from IBM and currently I am burning it to a cd/dvd right now.
The steps I've collected so far are from the net. can you please confirm and add on to the steps if there are any steps... (0 Replies)
Discussion started by: Adnans2k
0 Replies
10. Solaris
i booted into maintenance mode
boot -- -s
from the console
I got the
Root password for system maintenance (control-d to bypass)
I did control -d
and then logged in
it told me that I was booting into boot -s
but after I did a control -d and logged in
who -r shows
... (9 Replies)
Discussion started by: goya
9 Replies
LEARN ABOUT DEBIAN
debconf-set-selections
DEBCONF-SET-SELECTIONS(1) Debconf DEBCONF-SET-SELECTIONS(1)
NAME
debconf-set-selections - insert new default values into the debconf database
SYNOPSIS
debconf-set-selections file
debconf-get-selections | ssh newhost debconf-set-selections
DESCRIPTION
debconf-set-selections can be used to pre-seed the debconf database with answers, or to change answers in the database. Each question will
be marked as seen to prevent debconf from asking the question interactively.
Reads from a file if a filename is given, otherwise from stdin.
WARNING
Only use this command to seed debconf values for packages that will be or are installed. Otherwise you can end up with values in the
database for uninstalled packages that will not go away, or with worse problems involving shared values. It is recommended that this only
be used to seed the database if the originating machine has an identical install.
DATA FORMAT
The data is a series of lines. Lines beginning with a # character are comments. Blank lines are ignored. All other lines set the value of
one question, and should contain four values, each separated by one character of whitespace. The first value is the name of the package
that owns the question. The second is the name of the question, the third value is the type of this question, and the fourth value (through
the end of the line) is the value to use for the answer of the question.
Alternatively, the third value can be "seen"; then the preseed line only controls whether the question is marked as seen in debconf's
database. Note that preseeding a question's value defaults to marking that question as seen, so to override the default value without
marking a question seen, you need two lines.
Lines can be continued to the next line by ending them with a "" character.
EXAMPLES
# Force debconf priority to critical.
debconf debconf/priority select critical
# Override default frontend to readline, but allow user to select.
debconf debconf/frontend select readline
debconf debconf/frontend seen false
OPTIONS
--verbose, -v
verbose output
--checkonly, -c
only check the input file format, do not save changes to database
SEE ALSO
debconf-get-selections(1) (available in the debconf-utils package)
AUTHOR
Petter Reinholdtsen <pere@hungry.com>
2012-09-10 DEBCONF-SET-SELECTIONS(1)