dsw has it right. You can see the VLANs of virtual network adapters even if they are inside an etherchannel. My ent0 is on VLAN 10 and my ent1 is on VLAN 20. Here is an example from one of my boxes.
hi,
i tried to configure an VLAN interface on my SF280 based on the documentation on docs.sun.com
# ifconfig eri1000 plumb up
Oct 21 13:41:26 cmsmaster ip: ip_rput_dlpi(eri1000): DL_ERROR_ACK for DL_ATTACH_REQ(11), errno 8, unix 0
ifconfig: SIOCSLIFNAME for ip: eri1000: no such interface... (2 Replies)
Hi all,
so server: FreeBSD 7.0 release,
interfaces on it DLINK DGE-528T with support of vlans :))
so first interface looks to LAN second to ISP.
I created vlan1 with id 1 and gave to it ip address and plug it in
tagged port of swith for vlan 1. so client from vlan1 reaches the server.
it... (2 Replies)
Hi all
My application is a monitoring application that monitors the incoming udp packet when ever required. When ever a particular source ip and port and dest ip and port is provided the filter will be framed based them. For eg,
char filterExpr;
filterExpr = "udp and src host 192.168.16.100... (0 Replies)
Hello. I want to Communicate 2 VLAN with router like this solution:
http://8pic.ir/images/83m0ouih8mmm9s1sfl56.jpg
For this purpose I'm configuring 2 Linux system as a switch and connect 4 host to them. Then a router is added to scenario.
The configuration of the switches is:
On DUT1(Linux):... (1 Reply)
Hi,
Is it possible to VLAN tag with a ce interface on Solaris 9? Link speed is gb.
ce:0:ce0:link_speed 1000
I have a ce0 interface I would need to have access to another VLAN as well as the one it's currently on.
What commands would I need to run?
Thanks.;) (2 Replies)
We have two hosts in same vlan with same route rules.
One of them is not able to connect to an outside IP while in another I get "failed: Connection timed out" while testing the connectivity through netcat.
I have tried mtr /traceroute and it gives me the same results.
Is there a netcat... (1 Reply)
Have 2 nics on physical system
net0 phys 1500 up --
net1 phys 1500 up --
1. I want to create a link aggregation with LACP enabled with above 2 nics
2. Create port-group(Like we create on ESXi) with VLAN-ID 2141
3. And assign this... (0 Replies)
Hi Guys,
Our lpars is currently running on 2 different vlans (20, 30). Now we have a requirement that vlan 30 needs to be change to vlan 31 at the same subnet. I'm not sure on what is the best approach for this or what change is involve on the AIX side.
This is our setup.
Network switch -... (5 Replies)
Hi Folks,
I am currently moving systems to a new environment, with some changes to the network requirements on the systems.
One of these changes is moving from just standard IPMP to using IPMP on top of a VLAN, I have used VLAN tagging befor without issue - however not with IPMP.
What I... (2 Replies)
Discussion started by: gull04
2 Replies
LEARN ABOUT DEBIAN
vlan-interfaces
VLAN-INTERFACES(5) File formats VLAN-INTERFACES(5)NAME
/etc/network/interfaces (vlan) - vlan extensions for the interfaces(5) file format
DESCRIPTION
/etc/network/interfaces contains network interface configuration information for the ifup(8) and ifdown(8) commands. This manpage
describes the vlan extensions to the standard interfaces(5) file format.
Primary extensions exist to make and destroy vlan interfaces, secondary extensions exist for ipv4 interface manipulation which are gener-
ally needed when using (a lot of) vlans.
VLAN CREATION
Vlan interface definitions exist of the vlan interface name, and an optional 'raw-device' parameter. Vlan interfaces are numbered 1 to
4095. You have the option to have interface names zero-padded to 4 numbers, or just the plain digits without leading zero. The following
example shows four ways to create a vlan with id 1 on interface eth0. They all result in different names.
iface eth0.1 inet static
address 192.168.1.1
netmask 255.255.255.0
iface vlan1 inet static
vlan-raw-device eth0
address 192.168.1.1
netmask 255.255.255.0
iface eth0.0001 inet static
address 192.168.1.1
netmask 255.255.255.0
iface vlan0001 inet static
vlan-raw-device eth0
address 192.168.1.1
netmask 255.255.255.0
# We don't have br support out of the box
iface br0.2 inet static
vlan-raw-device br0
address 192.168.1.1
netmask 255.255.255.0
# Aliases are ignored
iface br0.2:1 inet static
address 192.168.1.1
netmask 255.255.255.255
EXTRA IFACE OPTIONS
Usually someone who uses vlans also wants to do some other manipulations with the ip stack or interface.
vlan-raw-device devicename
Indicates the device to create the vlan on. This is ignored when the devicename is part of the vlan interface name.
ip-proxy-arp 0|1
Turn proxy-arp off or on for this specific interface. This also works on plain ethernet like devices.
ip-rp-filter 0|1|2
Set the return path filter for this specific interface. This also works on plain ethernet like devices.
hw-mac-address mac-address
This sets the mac address of the interface before bringing it up. This works on any device that allows setting the hardware address
with the ip command.
AUTHOR
This manpage was adapted from interfaces(5) by Ard van Breemen <ard@kwaak.net>
SEE ALSO vconfig(8)interfaces(5)vlan September 30 2007 VLAN-INTERFACES(5)