01-26-2011
Hello
on the inactive node nothing should be mounted from that volumegroup - so all you need to do is
1. lspv - copy the output to somewhere so you know which disks belong to the volumegroup
2. exportvg yourvolumegroupname
3. importvg -V volumegroup major number -Ry volumegroupname PVID from any of the disks belonging to this volumegroup (you can look up the major number on the active node doing ls -ali /dev | grep volumegroupname - the major and minor number is stated beside the name - this import should happen hopefully without any errors - if you get an error than post it here so we can follow up on that
4. cluster synchronization is part of the hacmp menus in smitty - look under Extended Configuration ...
Kind regards
zxmaus
8 More Discussions You Might Find Interesting
1. High Performance Computing
I have rcently setup a 4 node cluster running sun cluster 3.2
and I have installed 4 zones on each node. when installing the zones I had to install the zone on all nodes the on the last node do a zlogin -C <zonename>
this worked ok.
theni I tried to siwitch the zone to node a thei work... (14 Replies)
Discussion started by: lesliek
14 Replies
2. Solaris
Hi,
I am running Solaris 10 + VCS 5 in one of our environment. Recently one of my colleague configured all resources in a single service group.( ie, one service group which has all resources) ,Usually we create seperate service groups for Hardware & for application.
For eg: SYS_HW_GRP, will... (0 Replies)
Discussion started by: mpics66
0 Replies
3. AIX
Hi,
I have a requirement to monitor the HACMP Resource Groups. At present in my environment, if the Resource Groups fail over from preferred node to Secondary node we dont get notification.
Can some one help me in creating a scrript. I have more than one RG online. (Max 4 Resource Groups in... (2 Replies)
Discussion started by: srnagu
2 Replies
4. AIX
Hi,
I have a 2 node Cluster. Which is working in active/passive mode (i.e Node#1 is running and when it goes down the Node#2 takes over)
Now there's this requirement that we need a mount point say /test that should be available in active node #1 and when node #1 goes down and node#2 takes... (6 Replies)
Discussion started by: aixromeo
6 Replies
5. AIX
Hi,
I'm new to HACMP. Currently I setup a cluster with nfs cross-mount follow this guide:
kristijan.org NFS cross-mounts in PowerHA/HACMPMy cluster has two nodes: erp01 and erp02.
I'm using nfs4 with filesystem for nfs is: /sapnfs
Cluster start without problems. But I cannnot move RG (with... (3 Replies)
Discussion started by: giobuon
3 Replies
6. AIX
Hello. I am Running AIX 6.1 and PowerHA 6.1
I have an active/active cluster (Prod/Dev) cluster. Each side will failover to the other.
I have on my prod side an active volume group with a file system. The VG is imported on both nodes and active (varried on, file system mounted) on the prod... (3 Replies)
Discussion started by: mhenryj
3 Replies
7. AIX
Hi all, I have the following in hacmp.out for bringing Resource group online.
Volume groups themselves are Enhanced-Capable and on each node I can varyon and mount filesystems.
+main1_rg_01:cl_activate_vgs STATUS=0
+main1_rg_01:cl_activate_vgs typeset -li STATUS
+main1_rg_01:cl_activate_vgs... (2 Replies)
Discussion started by: OdilPVC
2 Replies
8. AIX
Hello all,
I'm working to fix a two-node SysMirror cluster that uses NFS mounts from a NetApp appliance as the data repository. Currently all the NFS mounts/unmounts are called from the application controller scripts, and since file collection isn't currently working, (One fight at at time... (3 Replies)
Discussion started by: ZekesGarage
3 Replies
LEARN ABOUT DEBIAN
pvscan
PVSCAN(8) System Manager's Manual PVSCAN(8)
NAME
pvscan - scan all disks for physical volumes
SYNOPSIS
pvscan [-d|--debug] [-h|--help] [-v|--verbose] [--version] [--ignorelockingfailure] [-e|--exported] [-n|--novolumegroup] [-s|--short]
[-u|--uuid]
pvscan [-d|--debug] [-h|--help] --cache [--major major --minor minor | DevicePath ] ...
DESCRIPTION
pvscan scans all supported LVM block devices in the system for physical volumes.
OPTIONS
See lvm(8) for common options.
-e, --exported
Only show physical volumes belonging to exported volume groups.
-n, --novolumegroup
Only show physical volumes not belonging to any volume group.
-s, --short
Short listing format.
-u, --uuid
Show UUIDs (Uniform Unique Identifiers) in addition to device special names.
--cache [ --major major --minor minor | DevicePath ] ...
Scan one or more devices and instruct the lvmetad daemon to update its cached state accordingly. Called internally by udev rules.
All devices listed explicitly are processed regardless of any device filters set in lvm.conf.
SEE ALSO
lvm(8), pvcreate(8), pvdisplay(8)
Sistina Software UK LVM TOOLS 2.02.95(2) (2012-03-06) PVSCAN(8)