Sponsored Content
Operating Systems AIX HACMP resource group State not STABLE Post 302490839 by zxmaus on Tuesday 25th of January 2011 08:59:53 PM
Old 01-25-2011
Hi,

I would try to export and reimport the volumegroup in question on the inactive node. Make sure you keep the correct VG Major number (you can import using the -V flag).
If it finds all PVs you should just sync the cluster config and than try again. If it has problems during the import you can take it from there. I had similar issues after migrating storage across disks - duplicate pvid's on some disks - the cluster did not like that much.

Hope that helps,
regards
zxmaus
 

8 More Discussions You Might Find Interesting

1. High Performance Computing

sun Cluster resource group cant failover

I have rcently setup a 4 node cluster running sun cluster 3.2 and I have installed 4 zones on each node. when installing the zones I had to install the zone on all nodes the on the last node do a zlogin -C <zonename> this worked ok. theni I tried to siwitch the zone to node a thei work... (14 Replies)
Discussion started by: lesliek
14 Replies

2. Solaris

Solaris + VCS , move a resource to another group

Hi, I am running Solaris 10 + VCS 5 in one of our environment. Recently one of my colleague configured all resources in a single service group.( ie, one service group which has all resources) ,Usually we create seperate service groups for Hardware & for application. For eg: SYS_HW_GRP, will... (0 Replies)
Discussion started by: mpics66
0 Replies

3. AIX

Resource Group Monitoring

Hi, I have a requirement to monitor the HACMP Resource Groups. At present in my environment, if the Resource Groups fail over from preferred node to Secondary node we dont get notification. Can some one help me in creating a scrript. I have more than one RG online. (Max 4 Resource Groups in... (2 Replies)
Discussion started by: srnagu
2 Replies

4. AIX

Adding a Volume Group to an HACMP Resource Group?

Hi, I have a 2 node Cluster. Which is working in active/passive mode (i.e Node#1 is running and when it goes down the Node#2 takes over) Now there's this requirement that we need a mount point say /test that should be available in active node #1 and when node #1 goes down and node#2 takes... (6 Replies)
Discussion started by: aixromeo
6 Replies

5. AIX

HACMP, NFS cross-mount problem. Can not move resource group

Hi, I'm new to HACMP. Currently I setup a cluster with nfs cross-mount follow this guide: kristijan.org NFS cross-mounts in PowerHA/HACMPMy cluster has two nodes: erp01 and erp02. I'm using nfs4 with filesystem for nfs is: /sapnfs Cluster start without problems. But I cannnot move RG (with... (3 Replies)
Discussion started by: giobuon
3 Replies

6. AIX

Adding existing VG to powerHA Resource group

Hello. I am Running AIX 6.1 and PowerHA 6.1 I have an active/active cluster (Prod/Dev) cluster. Each side will failover to the other. I have on my prod side an active volume group with a file system. The VG is imported on both nodes and active (varried on, file system mounted) on the prod... (3 Replies)
Discussion started by: mhenryj
3 Replies

7. AIX

Power HA 6.1 Bring Resource group online issue

Hi all, I have the following in hacmp.out for bringing Resource group online. Volume groups themselves are Enhanced-Capable and on each node I can varyon and mount filesystems. +main1_rg_01:cl_activate_vgs STATUS=0 +main1_rg_01:cl_activate_vgs typeset -li STATUS +main1_rg_01:cl_activate_vgs... (2 Replies)
Discussion started by: OdilPVC
2 Replies

8. AIX

Sysmirror 7.1.3 Resource Group NFS mounts

Hello all, I'm working to fix a two-node SysMirror cluster that uses NFS mounts from a NetApp appliance as the data repository. Currently all the NFS mounts/unmounts are called from the application controller scripts, and since file collection isn't currently working, (One fight at at time... (3 Replies)
Discussion started by: ZekesGarage
3 Replies
CLUSTER(1)						      General Commands Manual							CLUSTER(1)

NAME
cluster - find clusters in a graph and augment the graph with this information. SYNOPSIS
cluster [-v?] [ -Ck ] [ -ck ] [ -o outfile ] [ files ] DESCRIPTION
cluster takes as input a graph in DOT format, finds node clusters and augments the graph with this information. The clusters are specified by the "cluster" attribute attached to nodes; cluster values are non-negative integers. cluster attempts to maximize the modularity of the clustering. If the edge attribute "weight" is defined, this will be used in computing the clustering. OPTIONS
The following options are supported: -Ck specifies a targeted number of clusters that should be generated. The specified number k is only a suggestion and may not be real- isable. If k == 0, the default, the number of clusters that approximately optimizes the modularity is returned. -ck specifies clustering method. If k == 0, the default, the modularity will be used. If k == 1 modularity quality will be used. -ooutfile Specifies that output should go into the file outfile. By default, stdout is used. -v Verbose mode. EXAMPLES
Applying cluster to the following graph, graph { 1--2 [weight=10.] 2--3 [weight=1] 3--4 [weight=10.] 4--5 [weight=10] 5--6 [weight=10] 3--6 [weight=0.1] 4--6 [weight=10.] } gives graph { node [cluster="-1"]; 1 [cluster=1]; 2 [cluster=1]; 3 [cluster=2]; 4 [cluster=2]; 5 [cluster=2]; 6 [cluster=2]; 1 -- 2 [weight="10."]; 2 -- 3 [weight=1]; 3 -- 4 [weight="10."]; 4 -- 5 [weight=10]; 5 -- 6 [weight=10]; 3 -- 6 [weight="0.1"]; 4 -- 6 [weight="10."]; } AUTHOR
Yifan Hu <yifanhu@research.att.com> SEE ALSO
gvmap(1) Blondel, V.D., Guillaume, J.L., Lambiotte, R., Lefebvre, E.: Fast unfolding of communities in large networks. Journal of Statistical Mechanics: Theory and Experiment (2008), P10008. 3 March 2011 CLUSTER(1)
All times are GMT -4. The time now is 12:30 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy