ntpdate(1M)						  System Administration Commands					       ntpdate(1M)

NAME

       ntpdate - set the date and time by way of NTP

SYNOPSIS

       /usr/sbin/ntpdate [-bBdoqsuv] [-a key#] [-e authdelay] [-k keyfile] [-m] [-o version] [-p samples] [-t timeout] [-w] server...

DESCRIPTION

       The  ntpdate  utility  sets the local date and time. To determine the correct time, it polls the Network Time Protocol (NTP) servers on the
       hosts given as arguments. This utility must be run as root on the local host. It obtains a number of samples from each of the  servers  and
       applies the standard NTP clock filter and selection algorithms to select the best of these.

       The  reliability  and precision of ntpdate improve dramatically with a greater number of servers. While a single server may be used, better
       performance and greater resistance to inaccuracy on the part of any one server can be obtained by providing at least three or four servers,
       if not more.

       The  ntpdate  utility makes time adjustments in one of two ways. If it determines that your clock is off by more than 0.5 seconds it simply
       steps the time by calling gettimeofday(3C). If the error is less than 0.5 seconds, by default, it slews the clock's time with  the  offset,
       by  way	of  a call to adjtime(2).  The latter technique is less disruptive and more accurate when the offset is small; it works quite well
       when ntpdate is run by cron every hour or two. The adjustment made in the latter case is actually 50% larger than the measured offset. This
       adjustment tends to keep a badly drifting clock more accurate, at some expense to stability. This tradeoff is usually advantageous. At boot
       time, however, it is usually better to step the time. This can be forced in all cases by specifying the -b option on the command line.

       The ntpdate utility declines to set the date if an NTP server daemon like xntpd(1M) is running on the same host. It can be run on a regular
       basis  from  cron(1M)  as an alternative to running a daemon. Doing so once every one to two hours results in precise enough timekeeping to
       avoid stepping the clock.

OPTIONS

       The following options are supported:

       -a key#	       Authenticate transactions, using the key number, key#.

       -b	       Step the time by calling gettimeofday(3C).

       -B	       Force the time to always be slewed using the adjtime(2) system call, even if the measured offset is greater than +-128  ms.
		       The  default  is  to  step  the	time  using settimeofday(3C) if the offset is greater than +-128 ms. If the offset is much
		       greater than +-128 ms in this case, that it can take a long time (hours) to slew the clock to  the  correct  value.  During
		       this time the host should not be used to synchronize clients.

       -d	       Display what will be done without actually doing it. Information useful for general debugging is also printed.

       -e authdelay    Specify	an  authentication processing delay, authdelay in seconds. See xntpd(1M) for details. This number is usually small
		       enough to be negligible for purposes of ntpdate. However, specifying a value may improve timekeeping on very slow CPU's.

       -k keyfile      Read keys from the file keyfile instead of the default file, /etc/inet/ntp.keys. keyfile should be in the format  described
		       in xntpd(1M).

       -m	       Join multicast group specified in server and synchronize to multicast NTP packets. The standard NTP group is 224.0.1.1.

       -o version      Force  the  program  to	poll  as a version 1 or version 2 implementation. By default ntpdate claims to be an NTP version 3
		       implementation in its outgoing packets.	However, some older software declines to respond to version 3 queries. This option
		       can be used in these cases.

       -p samples      Set the number of samples ntpdate acquires from each server. samples can be between 1 and 8 inclusive. The default is 4.

       -q	       Query only. Do not set the clock.

       -s	       Log  actions  by way of the syslog(3C) facility rather than to the standard output -- a useful option when running the pro-
		       gram from cron(1M).

       -t timeout      Set the time ntpdate spends, waiting for a response. timeout is rounded to a multiple of 0.2 seconds. The default is 1 sec-
		       ond, a value suitable for polling across a LAN.

       -u	       Use  an unprivileged port to send the packets from. This option is useful when you are behind a firewall that blocks incom-
		       ing traffic to privileged ports, and you want to synchronize with hosts beyond the firewall.  The  -d  option  always  uses
		       unprivileged ports.

       -v	       Be verbose. This option causes ntpdate's version identification string to be logged.

       -w	       Wait until able to synchronize with a server. When the -w option is used together with -m, ntpdate waits until able to join
		       the group and synchronize.

FILES

       /etc/inet/ntp.keys      Contains the encryption keys used by ntpdate.

ATTRIBUTES

       See attributes(5) for descriptions of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE	     |	    ATTRIBUTE VALUE	   |
       +-----------------------------+-----------------------------+
       |Availability		     |SUNWntpu			   |
       +-----------------------------+-----------------------------+

SEE ALSO

       cron(1M), xntpd(1M), adjtime(2), gettimeofday(3C), settimeofday(3C)syslog(3C),  attributes(5)

NOTES

       The technique of compensating for clock oscillator errors to improve accuracy is inadequate. However, to  further  improve  accuracy  would
       require the program to save state from previous runs.

SunOS 5.10							    29 Sep 1999 						       ntpdate(1M)