01-22-2011
I would connect a known good machine to the same cable with the same network configuration as the Solaris 10 machine so you can be 100% certain whether or not its related to the Solaris machine or your network infrastructure.
If it is your network infrastructure I would check to see if you are using port security on the switch you are connected to (if so configure the switch with your Solaris 10 machines e1000g0 NIC's MAC address), that the port is in the correct vlan, and that the port on the switch is enabled.
10 More Discussions You Might Find Interesting
1. Solaris
Withouth being physically at the server, is there a way to tell if the network cable is unplugged? (6 Replies)
Discussion started by: csaunders
6 Replies
2. Solaris
I have a solaris x86 box that ive been having trouble getting on my network, anyone know a good guide that can take me through it step by step? (1 Reply)
Discussion started by: xtremepancakez
1 Replies
3. Solaris
Hi gurus,
I need book to learn about network in Solaris 9
Thanks (2 Replies)
Discussion started by: mass1123
2 Replies
4. Solaris
I have installed solaris x86 on a standalone PC. Now I have connected a LAN cable to it. What do I do next for further configuration or to access internet from that solaris machine? (16 Replies)
Discussion started by: panchpan
16 Replies
5. Solaris
hi all,
how do i change the routing info and make sure i will be able to connect remotely?
any ideas please?
thanks in advance. (5 Replies)
Discussion started by: itik
5 Replies
6. Solaris
Hi,
i have installed solaris on virtual box in my desktop, i wanted to know how to make it network enabled(nated network). Nated network means it will use same IP as of my windows right? so is it possible that using the same IP i can enable the network on this virtual box.
Thanks in advance. (3 Replies)
Discussion started by: amult
3 Replies
7. Solaris
Hi,
I'm very new to Solaris world and istarted my learnign with a Blade T6320 Server.
I was trying to install Solaris 10.8 from a DVD image over the network.
But from the client(the machine which i want to install Solaris) when i tried boot net , i am getting a message like " cannto find... (5 Replies)
Discussion started by: jerinvjose
5 Replies
8. Solaris
Hi,
Need help for the network configuration on Solaris 10 5/8.
My NIC's dirver was loaded after Solaris installation and is configured using static ip address for a local network: 172.16.1.12
I have configured set of files as: /etc/hosts :
172.16.1.12 ls12
/etc/hostname.iprb0:... (7 Replies)
Discussion started by: dn100
7 Replies
9. Solaris
Hi all,
I got a Fujitsu P650 server running on Solaris 9 and we are going to re-install Solaris 10 . W have a build server in a different IP segment. So we setup a boot server and /etc/ethers and /etc/bootparams are all updated. When I issue
boot net -install,
I'm getting the following... (3 Replies)
Discussion started by: mohzub
3 Replies
10. Solaris
Dear All,
I have a solaris Server in which I have 4 network interfaces , out of which only one is used . So all the applications are using this interface .
The interface speed is 1000Mbps . I find no hardware issue or packets g being dropped.
But i find that no of Input and Output... (4 Replies)
Discussion started by: jegaraman
4 Replies
LEARN ABOUT OPENDARWIN
auscope
AUSCOPE(1) General Commands Manual AUSCOPE(1)
NAME
auscope - Network Audio System Protocol Filter
SYNOPSIS
auscope [ option ] ...
DESCRIPTION
auscope is an audio protocol filter that can be used to view the network packets being sent between an audio application and an audio
server.
auscope is written in Perl, so you must have Perl installed on your machine in order to run auscope. If your Perl executable is not
installed as /usr/local/bin/perl, you should modify the first line of the auscope script to reflect the Perl executable's location. Or,
you can invoke auscope as
perl auscope [ option ] ...
assuming the Perl executable is in your path.
To operate, auscope must know the port on which it should listen for audio clients, the name of the desktop machine on which the audio
server is running and the port to use to connect to the audio server. Both the output port (server) and input port (client) are automati-
cally biased by 8000. The output port defaults to 0 and the input port defaults to 1.
ARGUMENTS
-i<input-port>
Specify the port that auscope will use to take requests from clients.
-o<output-port>
Determines the port that auscope will use to connect to the audio server.
-h<audio server name>
Determines the desktop machine name that auscope will use to find the audio server.
-v<print-level>
Determines the level of printing which auscope will provide. The print-level can be 0 or 1. The larger numbers provide greater
output detail.
EXAMPLES
In the following example, mcxterm is the name of the desktop machine running the audio server, which is connected to the TCP/IP network
host tcphost. auscope uses the desktop machine with the -h command line option, will listen for client requests on port 8001 and connect
to the audio server on port 8000.
Ports (file descriptors) on the network host are used to read and write the audio protocol. The audio client auplay will connect to the
audio server via the TCP/IP network host tcphost and port 8001:
auscope -i1 -o0 -hmcxterm
auplay -audio tcp/tcphost:8001 dial.snd
In the following example, the auscope verbosity is increased to 1, and the audio client autool will connect to the audio server via the
network host tcphost, while displaying its graphical interface on another server labmcx:
auscope -i1 -o0 -hmcxterm -v1
autool -audio tcp/tcphost:8001 -display labmcx:0.0
SEE ALSO
nas(1), perl(1)
COPYRIGHT
Copyright 1994 Network Computing Devices, Inc.
AUTHOR
Greg Renda, Network Computing Devices, Inc.
1.9.3 AUSCOPE(1)