|
|
Sponsored Content
Top Forums
Shell Programming and Scripting
Using Variables with SED
Post 302489779 by miyoung999 on Friday 21st of January 2011 03:25:23 PM
01-21-2011
|
|
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi,
I'm trying to do the following , I have certain variables in a file and then I want to check for these variables in a certain cobol file to see if they contain a certain package if so replace them with value 1 but but that last line is giving problems:
# for each variable in SQL file
... (1 Reply)
Discussion started by: seaten
1 Replies
2. Shell Programming and Scripting
Hi,
I'm trying to do the following , I have certain variables in a file and then I want to check for these variables in a certain cobol file to see if they contain a certain package if so replace them with value 1 but but that last line is giving problems:
# for each variable in SQL file
... (1 Reply)
Discussion started by: seaten
1 Replies
3. UNIX for Dummies Questions & Answers
Hi guys,
I want to replace certain values with the number 1.
But it is also replacing other values which contain the value I want to replace. e.g.:
I want to replace ID-INTERNAL with 1, that's no problem but it will also replace ID-INTERNAL-NON-REM with 1-NON-REM
I don't want to... (10 Replies)
Discussion started by: seaten
10 Replies
4. Shell Programming and Scripting
when i do something like substituting a particular thing with a system variable, i am unable to do that expect the varible name getting into that.
for ex.. i tried,
sed -e 's/date/`date`/g' <if >of
but i got date replaced with "`date`" and not with the actual date ..
same case happened... (5 Replies)
Discussion started by: sskb
5 Replies
5. Shell Programming and Scripting
Hi,
I'm trying to use sed to delete the last three lines of a file. I currently have:
# get the amount of lines in the file
foldernum=`wc -l File_In.txt | cut -c1-8`
# remove the lines in the file
sed "${foldernum}-3,${foldernum}d" File_In.txt > File_Out.txt
I get the error - sed:... (5 Replies)
Discussion started by: Mr_Plow
5 Replies
6. Shell Programming and Scripting
HELP!!!
I'm keep getting "sed: Function s/PETS/dog cannot be parsed."
I have 2 files that list...
# cat FILE1.txt
dog
cat
mouse
# cat FILE2.txt
my pets are
PETS
I put this into a variable...
# A=`cat FILE1.txt`
# sed "s/PETS/$A" FILE2.txt > FILE3.txt (5 Replies)
Discussion started by: Zenwork
5 Replies
7. Shell Programming and Scripting
I'm trying to get sed to cut and replace using variables, but it doesnt seem to work, when I run this the mod time of the file does get updated. Is my syntax incorrect in the sed command?
Thanks
#!/usr/bin/ksh
#Modify header
set -x
HEAD=$(cat PBN2CPR1.TXT | awk 'BEGIN { FS = ","... (1 Reply)
Discussion started by: ddurden7
1 Replies
8. UNIX for Dummies Questions & Answers
Hi,
I am able to use sed if I hardcode the find and replace values in a shell script.
This works:
sed -e 's/123v/4567/g' /path/aaa.txt
> /path/aaa.txt.tmp
If I use a variable, I am not able to use sed command. why?
This doesnot work:
i=abc
j=bk${i}
sed -e 's/${i}/${j}/g'... (5 Replies)
Discussion started by: new_learner
5 Replies
9. Shell Programming and Scripting
Is it possible to place a variable in a sed command as such?
sed 's/ret_Priv()/$var/' <filename>
I am doing this under Bourne. (5 Replies)
Discussion started by: plslakewood
5 Replies
10. Shell Programming and Scripting
Im trying to use sed to print value that matches the value in variable and all lines after that.
grep "Something" test.txt | sed -e '/{$variable}/,$b' -e 'd'
I cant get it work, if I replace the $variable with the value it contains, it works fine... (10 Replies)
Discussion started by: olkkis
10 Replies
LEARN ABOUT MINIX
faith
FAITH(4) BSD Kernel Interfaces Manual FAITH(4) NAME
faith -- IPv6-to-IPv4 TCP relay capturing interface SYNOPSIS
device faith DESCRIPTION
The faith interface captures IPv6 TCP traffic, for implementing userland IPv6-to-IPv4 TCP relay like faithd(8). Each faith interface is created at runtime using interface cloning. This is most easily done with the ifconfig(8) create command or using the cloned_interfaces variable in rc.conf(5). Special action will be taken when IPv6 TCP traffic is seen on a router, and the routing table suggests to route it to the faith interface. In this case, the packet will be accepted by the router, regardless of the list of IPv6 interface addresses assigned to the router. The packet will be captured by an IPv6 TCP socket, if it has the IN6P_FAITH flag turned on and matching address/port pairs. As a result, faith will let you capture IPv6 TCP traffic to some specific destination addresses. Userland programs, such as faithd(8) can use this behavior to relay IPv6 TCP traffic to IPv4 TCP traffic. The program can accept some specific IPv6 TCP traffic, perform getsockname(2) to get the IPv6 destination address specified by the client, and perform application-specific address mapping to relay IPv6 TCP to IPv4 TCP. The IN6P_FAITH flag on a IPv6 TCP socket can be set by using setsockopt(2), with level IPPROTO_IPV6 and optname IPv6_FAITH. To handle error reports by ICMPv6, some ICMPv6 packets routed to an faith interface will be delivered to IPv6 TCP, as well. To understand how faith can be used, take a look at the source code of faithd(8). As the faith interface implements potentially dangerous operations, great care must be taken when configuring it. To avoid possible misuse, the sysctl(8) variable net.inet6.ip6.keepfaith must be set to 1 prior to using the interface. When net.inet6.ip6.keepfaith is 0, no packets will be captured by the faith interface. The faith interface is intended to be used on routers, not on hosts. SEE ALSO
inet(4), inet6(4), faithd(8) Jun-ichiro itojun Hagino and Kazu Yamamoto, An IPv6-to-IPv4 transport relay translator, RFC3142. HISTORY
The FAITH IPv6-to-IPv4 TCP relay translator first appeared in the WIDE hydrangea IPv6 stack. BSD
April 10, 1999 BSD