Hello, I am using awk to split a file into multiple files using command:
nawk '{
if ( $1 == "<process" )
{
n=split($2, arr, "\"");
file=arr
}
print > file }' processes.xml
<process name="Process1.process">
... (3 Replies)
Hi,
I've one requirement. I have to split one comma delimited file into multiple files based on one of the column values.
How can I achieve this Unix
Here is the sample data. In this case I have split the files based on date column(c4)
Input file
c1,c2,c3,c4,c5... (1 Reply)
I have one single shown below and I need to break each ST|850 & SE to separate file using unix script. Below example should create 3 files. We can use ST & SE to filter as these field names will remain same.
Please advice with the unix code.
ST|850
BEG|PO|1234
LIN|1|23
SE|4
ST|850... (3 Replies)
The following code will split the infile into multiple files. However, I need it to insert the same first 3 lines from the original input file into each splitted file. How do I modify my script below to do so:
print -n "Enter file name to split? " ; read infile
if
then
echo "Invalid file... (4 Replies)
Help needed urgently please.
I have a large file - a few hundred thousand lines.
Sample
CP START ACCOUNT
1234556
name 1
CP END ACCOUNT
CP START ACCOUNT
2224444
name 1
CP END ACCOUNT
CP START ACCOUNT
333344444
name 1
CP END ACCOUNT
I need to split this file each time "CP START... (7 Replies)
I have a requirement to split a huge file to smaller text files based on first four characters which look like
ABCD
1234
DFGH
RREX
:
:
:
:
:
0000
Each of these records are OF EQUAL bytes with a different internal layout based on the above first digit identifier..
Any help to start... (5 Replies)
Hi,
I have a Huge 7 GB file which has around 1 million records, i want to split this file into 4 files to contain around 250k messages each.
Please help me as Split command cannot work here as it might miss tags..
Format of the file is as below
<!--###### ###### START-->... (6 Replies)
Hi,
I have a text file (attached the sample). I have also, attached the way the way the files need to be split.
We get this file, that will either have 24 Jurisdictions, or will miss some and retain some.
Like in the attached sample file, there are only Jurisdictions 03,11,14,15, 20 and 30.... (3 Replies)
Hi All,
I have the sales_data.csv file in the directory as below.
SDDCCR; SOM ; MD6546474777 ;05-JAN-16
ABC ; KIRAN ; CB789 ;04-JAN-16
ABC ; RAMANA; KS566767477747 ;06-JAN-16
ABC ; KAMESH; A33535335 ;04-JAN-16
SDDCCR; DINESH; GD6674474747 ;08-JAN-16... (4 Replies)
I am using below code to split files based on blank lines but it does not work.
awk 'BEGIN{i=0}{RS="";}{x="F"++i;}{print > x;}'
Your help would be highly appreciated
find attachment of sample.txt file (2 Replies)
Discussion started by: imranrasheedamu
2 Replies
LEARN ABOUT DEBIAN
mrtg-ping-probe
MRTG-PING-PROBE(1) General Commands Manual MRTG-PING-PROBE(1)NAME
mrtg-ping-probe - ping probe module for Multi Router Traffic Grapher
DESCRIPTION
mrtg-ping-probe is a ping probe module for MRTG 2.x. It is used to monitor the round trip time and packet loss to networked devices. MRTG
uses the output of mrtg-ping-probe to generate graphs visualizing minimum and maximum round trip times or packet loss.
mrtg-ping-probe is not run directly, but is called by MRTG as a helper when it needs to determine ping time to a host.
Act responsibly: do not use mrtg-ping-probe to ping devices without the owner's permission. Just imagine if 10,000 people decided to ping
your hosts! mrtg-ping-probe is meant to be used within your network to get round trip time performance figures for your network.
OPTIONS
To use mrtg-ping-probe you need to configure MRTG to call it from within the definition of a target host. This is done in the MRTG config
file, which is usually /etc/mrtg.conf.
Here's an example snippet: change the target name and IP address to suit your needs.
Target[your.target.ping]: `/usr/bin/mrtg-ping-probe 123.456.789.123`
SetEnv[your.target.ping]: MRTG_INT_IP="123.456.789.123" MRTG_INT_DESCR="ping"
MaxBytes[your.target.ping]: 100
AbsMax[your.target.ping]: 200
Options[your.target.ping]: gauge, growright
YLegend[your.target.ping]: ping time (ms)
ShortLegend[your.target.ping]: ms
Legend1[your.target.ping]: Maximum Round Trip Time in ms
Legend2[your.target.ping]: Minimum Round Trip Time in ms
Legend3[your.target.ping]: Maximal 5 Minute Maximum Round Trip Time in ms
Legend4[your.target.ping]: Maximal 5 Minute Minimum Round Trip Time in ms
LegendI[your.target.ping]: Max:
LegendO[your.target.ping]: Min:
Pay close attention to the backticks in the first line which tell MRTG to execute the nominated external program. Note also that you need
to use the "gauge" option, since the results of subsequent ping probes are independant values and not an incrementing counter.
SEE ALSO mrtg(1).
The latest release of mrtg-ping-probe can be found on the web at http://pwo.de/projects/mrtg/
AUTHOR
This manual page was written by Jonathan Oxer <jon@debian.org>, for the Debian project (but may be used by others).
April 14, 2003 MRTG-PING-PROBE(1)