01-14-2011
thanks for reply ...can u tell more detail about the stripes in Solaris point of view...
8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi all
This is my first thread here.i confused with the concept of thread.Can anyone tell me this concept in detail.my Quation may be at primary level.
Thanx in advance for help. (1 Reply)
Discussion started by: vishwasrao
1 Replies
2. UNIX for Dummies Questions & Answers
Hi all,
I am new here ,i want to know about interrupts in detail.What r
Interrupts .how they r handeled.
Thanx in adavnce. (1 Reply)
Discussion started by: vishwasrao
1 Replies
3. UNIX for Dummies Questions & Answers
Hi
Can someone tell me what are the differences between software and hardware raid ?
thx for help. (2 Replies)
Discussion started by: presul
2 Replies
4. Solaris
Dear ALl,
I have a RAID 5 volume which is as below
d120 r 60GB c1t2d0s5 c1t3d0s5 c1t4d0s5 c1t5d0s5
d7 r 99GB c1t2d0s0 c1t3d0s0 c1t4d0s0 c1t5d0s0
d110 r 99GB c1t2d0s4 c1t3d0s4 c1t4d0s4 c1t5d0s4
d8 r 99GB c1t2d0s1 c1t3d0s1... (2 Replies)
Discussion started by: jegaraman
2 Replies
5. Solaris
Hello All,
I have read enough of texts on Raid 01 and Raid 10 on solaris :wall: . But no-where found a way to create them using SVM. Some one pls tell me how to do or Post some link if that helps.
TIA
Curious
solarister (1 Reply)
Discussion started by: Solarister
1 Replies
6. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
7. Solaris
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Discussion started by: KhawHL
4 Replies
8. Red Hat
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
LEARN ABOUT XFREE86
vwright
VWRIGHT(1) General Commands Manual VWRIGHT(1)
NAME
vwright - normalize a RADIANCE view, shift it to the right
SYNOPSIS
vwright [ view options ] distance
vwright [ view options ] name
DESCRIPTION
In the first form, vwright shifts a RADIANCE view the specified distance to the right, putting out a complete set of view parameters in a
single line on the standard output. This utility is most often used to compute a right-eyed view from a left-eye view for stereo imaging.
If no options are specified on the command line, vwright reads a view from its standard input.
The distance given is in world coordinate units. A negative value indicates a shift to the left rather than the right.
The second form substitutes a name prefix in place of the shift distance, and produces constant assignments on the standard output suitable
for passing directly to rcalc(1). For a given prefix N, the constant names are as follows:
Nt: view type ('v'==1,'l'==2,'a'==3,'h'==4,'c'==5,'s'==6)
Npx: view point x value
Npy: view point y value
Npz: view point z value
Ndx: view direction x value (normalized)
Ndy: view direction y value (normalized)
Ndz: view direction z value (normalized)
Nd: view focal distance
Nux: view up vector x value (normalized)
Nuy: view up vector y value (normalized)
Nuz: view up vector z value (normalized)
Nh: view horizontal size
Nv: view vertical size
Ns: view shift
Nl: view lift
No: view fore clipping distance
Na: view aft clipping distance
Nhx: derived horizontal image vector x value (normalized)
Nhy: derived horizontal image vector y value (normalized)
Nhz: derived horizontal image vector z value (normalized)
Nhn: derived horizontal image vector multiplier
Nvx: derived vertical image vector x value (normalized)
Nvy: derived vertical image vector y value (normalized)
Nvz: derived vertical image vector z value (normalized)
Nvn: derived vertical image vector multiplier
EXAMPLES
To start rpict(1) on a view .06 meters left of the view in the file "right.vf":
rpict `vwright -.06 < right.vf` scene.oct > right.hdr &
To move the rad(1) view named "left" 2.5 inches to the right and render from there:
rad -v "right `rad -n -s -V -v left examp.rif | vwright 2.5`" examp.rif &
To pass a view to rcalc for conversion to some other view:
rcalc -n -e `vwright orig < orig.vf` -f viewmod.cal -o view.fmt > new.vf
AUTHOR
Greg Ward
SEE ALSO
pdfblur(1), rad(1), rcalc(1), rpict(1), rvu(1)
RADIANCE
8/29/96 VWRIGHT(1)