It means a concatenation of two partitions, end-to-end, into one partition.
If you had something like:
That would mean to stripe the two partitions into one partition.
Ie they are again added together, but this time in stripes across the whole new partition.
Hi all
This is my first thread here.i confused with the concept of thread.Can anyone tell me this concept in detail.my Quation may be at primary level.
Thanx in advance for help. (1 Reply)
Dear ALl,
I have a RAID 5 volume which is as below
d120 r 60GB c1t2d0s5 c1t3d0s5 c1t4d0s5 c1t5d0s5
d7 r 99GB c1t2d0s0 c1t3d0s0 c1t4d0s0 c1t5d0s0
d110 r 99GB c1t2d0s4 c1t3d0s4 c1t4d0s4 c1t5d0s4
d8 r 99GB c1t2d0s1 c1t3d0s1... (2 Replies)
Hello All,
I have read enough of texts on Raid 01 and Raid 10 on solaris :wall: . But no-where found a way to create them using SVM. Some one pls tell me how to do or Post some link if that helps.
TIA
Curious
solarister (1 Reply)
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
LEARN ABOUT MINIX
fdisk
FDISK(8) System Manager's Manual FDISK(8)NAME
fdisk - partition a hard disk [IBM]
SYNOPSIS
fdisk [-hm] [-sn] [file]
OPTIONS -h Number of disk heads is m
-s Number of sectors per track is n
EXAMPLES
fdisk /dev/hd0 # Examine disk partitions
fdisk -h9 /dev/hd0 # Examine disk with 9 heads
DESCRIPTION
When fdisk starts up, it reads in the partition table and displays it. It then presents a menu to allow the user to modify partitions,
store the partition table on a file, or load it from a file. Partitions can be marked as MINIX, DOS or other, as well as active or not.
Using fdisk is self-explanatory. However, be aware that repartitioning a disk will cause information on it to be lost. Rebooting the sys-
tem immediately is mandatory after changing partition sizes and parameters. MINIX, XENIX, PC-IX, and MS-DOS all have different partition
numbering schemes. Thus when using multiple systems on the same disk, be careful.
Note that MINIX, unlike MS-DOS , cannot access the last sector in a partition with an odd number of sectors. The reason that odd partition
sizes do not cause a problem with MS-DOS is that MS-DOS allocates disk space in units of 512-byte sectors, whereas MINIX uses 1K blocks.
Fdisk has a variety of other features that can be seen by typing h.
Fdisk normally knows the geometry of the device by asking the driver. You can use the -h and -s options to override the numbers found.
SEE ALSO part(8).
FDISK(8)