It means a concatenation of two partitions, end-to-end, into one partition.
If you had something like:
That would mean to stripe the two partitions into one partition.
Ie they are again added together, but this time in stripes across the whole new partition.
Hi all
This is my first thread here.i confused with the concept of thread.Can anyone tell me this concept in detail.my Quation may be at primary level.
Thanx in advance for help. (1 Reply)
Dear ALl,
I have a RAID 5 volume which is as below
d120 r 60GB c1t2d0s5 c1t3d0s5 c1t4d0s5 c1t5d0s5
d7 r 99GB c1t2d0s0 c1t3d0s0 c1t4d0s0 c1t5d0s0
d110 r 99GB c1t2d0s4 c1t3d0s4 c1t4d0s4 c1t5d0s4
d8 r 99GB c1t2d0s1 c1t3d0s1... (2 Replies)
Hello All,
I have read enough of texts on Raid 01 and Raid 10 on solaris :wall: . But no-where found a way to create them using SVM. Some one pls tell me how to do or Post some link if that helps.
TIA
Curious
solarister (1 Reply)
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
LEARN ABOUT FREEBSD
hv_vmbus
HYPER-V(4) BSD Kernel Interfaces Manual HYPER-V(4)NAME
hv_vmbus -- Hyper-V Virtual Machine Bus (VMBus) Driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in the system kernel configuration file:
device hyperv
DESCRIPTION
The hv_vmbus provides a high performance communication interface between guest and root partitions in Hyper-V. Hyper-V is a hypervisor-based
virtualization technology from Microsoft. Hyper-V supports isolation in terms of a partition. A partition is a logical unit of isolation,
supported by the hypervisor, in which operating systems execute.
The Microsoft hypervisor must have at least one parent, or root, partition, running Windows Server operating system. The virtualization
stack runs in the parent partition and has direct access to the hardware devices. The root partition then creates the child partitions which
host the guest operating systems.
Child partitions do not have direct access to other hardware resources and are presented a virtual view of the resources, as virtual devices
(VDevs). Requests to the virtual devices are redirected either via the VMBus or the hypervisor to the devices in the parent partition, which
handles the requests.
The VMBus is a logical inter-partition communication channel. The parent partition hosts Virtualization Service Providers (VSPs) which com-
municate over the VMBus to handle device access requests from child partitions. Child partitions host Virtualization Service Consumers
(VSCs) which redirect device requests to VSPs in the parent partition via the VMBus. The Hyper-V VMBus driver defines and implements the
interface that facilitate high performance bi-directional communication between the VSCs and VSPs. All VSCs utilize the VMBus driver.
SEE ALSO hv_ata_pci_disengage(4), hv_netvsc(4), hv_storvsc(4), hv_utils(4)HISTORY
Support for hv_vmbus first appeared in FreeBSD 10.0. The driver was developed through a joint effort between Citrix Incorporated, Microsoft
Corporation, and Network Appliance Incorporated.
AUTHORS
FreeBSD support for hv_vmbus was first added by Microsoft BSD Integration Services Team <bsdic@microsoft.com>.
BSD September 10, 2013 BSD